Radio & Antique Equipment Parts

Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"

Wipes out scratches in wood radio cabinets quick as a wink. Simply rub end of stick over scratches in any type of wood and watch them disappear like magic.

Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features

• Primary: 4000 turns, #41 wire (lugs 4 & 2)
• Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
• Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
• Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
• Lamination Core Size: 5/8" x 1/2"
• Weight: 7 oz.

This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:

• 6L6
• 6AU6
• 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.

New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

Premium quality wool felt washers. Medium brown in color, these washers will resist wear and hold their shape over time. Center holes already punched. ¼" inside diameter. Listed diameter is outside diameter. Washer is 1/16" thick.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Adhesive backing for lamenating to other washers to increase thickness. Overall dimensions 7/8" dia. x 1/8" thick.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. Allows proper dial centering in cabinet opening. Overall dimensions 0.875" dia. x .233" thick.

18 gauge braided power cord in gold - approximates the look of vintage power cords. 105°C temperature rating, 600V.

Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.

#20 stranded copper wire with modern insulation and lacquered cotton braid finish. Provides safety and authentic vintage look. 105°C temperature rating, 600V. For a solid core version, see: S-W8XL

300V wire nuts for use with 18 gauge through 22 gauge wires. These wire nuts are great for use on appliances, televisions, stereos, antennas, or for any small wiring application. Rated for up to 105°C.