Radio & Antique Equipment Parts
Bearing - Leslie, Upper Tension Idler
Sealed upper tension idler bearing for Leslies
Vibrator - 12 Volt, 3 Pin, Negative Ground
New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Belt - Leslie, 31", Lower Drive, for 122/147, Polyurethane
Replacement lower drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 31 in. diameter with a sanded seam to ensure a smooth drive.
Cable - Power All, Green Right Angle Line-6 Extension Jumper
Included in the Power-All system and also sold separately, the Cable-Green Right Angle jumper allows the user to power Line-6 Stomp-Box modelers and other digital effect units from the PA-9. The Cable-Green features a reverse-polarity (tip positive), right-angle male barrel connector with a larger, 2.5 mm internal diameter and spring-loaded clips.
Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
- Primary: 4000 turns, #41 wire (lugs 4 & 2)
- Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
- Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
- Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
- Lamination Core Size: 5/8" x 1/2"
- Weight: 7 oz.
Cable - Power All, 11 Lead Right Angle Daisy Chain
Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.
Cable - Power All, Red Right Angle Reverse Polarity Jumper
Included in the Power-All System and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.
Grommet Kit - All Rubber Parts, for Leslie
Package of 33Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.
Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
- Voltage: 9VDC
- Current: 200mA
- Tip positive; Sleeve negative
Coil - Miniature adjustable coil, 70, oscillator
Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.
Diode - 1N34A Germanium, low leakage
The 1N34A Germanium diode is an old standby in electronics. Widely used for detecting the rectifying efficiency or for switching on a radio, TV or stereo etc.
Nut - Wire nut, Small size for 16 - 18 gauge wire
Package of 12Small wire nuts, for use on appliances, televisions, stereos, antennas, or for any small wiring application.
Alignment Tool - Zenith-Admiral Hex Wrench
GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.
- End 1 - 0.027 in.
- End 2 - 0.1 in.
- End 3 - 0.1 in.