Radio & Antique Equipment Parts

Lower slow motor rebuild kit for Leslie models 122/147. Includes installation instructions.

Replacement lower drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 31 in. diameter with a sanded seam to ensure a smooth drive.

6 pin male plug with wavy washer, for Leslies.

Plug cover kit for Leslie , screws included. This is the connector cap for the connecting cable.

Designed to fit over unused male barrel connectors on a daisy chain or power supply, Cable-Caps protect against short circuits that can occur when a live lead touches a metal surface. Sold in sets of three. Fits over standard 5.5 mm diameter barrel plug connectors.

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects.

6 pin female socket with wavy washer, for Leslies.

17" diameter rotor cover fits Leslie models 122/147. 13" in height. Replace torn or missing rotor covers.

Removes fine scratches, abrasions and haziness from plastic surfaces. Great for plastic radio dial windows. For best results, follow with Novus No. 1 polish.

GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.

• End 1 - 0.027 in.
• End 2 - 0.1 in.
• End 3 - 0.1 in.

Replacement rubber O ring for the Leslie 122 and 147 cabinets.

Spring clip ¾" long for up to 15 ga. wire. Hole fits U.S. Screw size # 6.

Sealed upper tension idler bearing for Leslies

Sealed lower rotor bearing for Leslies.

300V wire nuts for use with 18 gauge through 22 gauge wires. These wire nuts are great for use on appliances, televisions, stereos, antennas, or for any small wiring application. Rated for up to 105°C.

Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.

Cleans and glazes plastic surface polish out and protect against small scratches, finger markings, dust build-up, and other markings. Significantly reduces haziness and is anti-static.

Butyrate shaft 6-1/8" long with 1/8" wide steel tips. Tip on one end recessed.

• Material: Conductive Nylon Metal
• End: 1/8"
• End 2: 1/8"

Replacement upper belt tension spring for Leslies.

Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a ⅛" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the ECO-Dapter® itself.

Reliable replacement relay for the Leslie 122. The small size makes this high quality relay easy to retrofit in the 122. Its performance exceeds the original relays used in the Leslie 122 with its very low switching noise and high ratings on both the contacts and the coil.
Features:

• 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
• Coil EMC suppression
• Cadmium Free contact material

New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects. Power-All® kits include a variety of useful cables for powering multiple pedals to the ECO-Dapter® 9V supply.

Small wire nuts, for use on appliances, televisions, stereos, antennas, or for any small wiring application.