Power Supplies & Accessories

F-Z-KIT Fuse Set - Fast and Slow Blow, 0.25" x 1.25", 8 types, 20 each
Package of 160
Fuse kit, fast and slow blow. Contains the following fuses:
  • 20x Slo-Blo, 2 Amp F-Z3AG-S2
  • 20x Slo-Blo, 3 Amp F-Z3AG-S3
  • 20x Slo-Blo, 1 Amp F-Z3AG-S1
  • 20x Slo-Blo, 4 Amp F-Z3AG-S4
  • 20x Slo-Blo, 5 Amp F-Z3AG-S5
  • 20x Fast-Blo, 2.5 Amp F-Z3AG-F2D5
  • 20x Fast-Blo, 1 Amp F-Z3AG-F1
  • 20x Fast-Blo, 3 Amp F-Z3AG-F3
$88.95
F-Z3AG-F Fuse - Fast-Blow, 250V, 3AG, 0.25" x 1.25"
Package of 5
Protect your expensive investment or hobby with inexpensive fuses.
Starting at $2.25
F-ZGMD-S Fuse - Slow-Blow, 250V, Miniature, 5mm x 20mm
Package of 5
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5
$3.50
F-Z3AG-S Fuse - Slow-Blow, 250V, 3AG, 0.25" x 1.25"
Package of 5
The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.
$3.25
M-ATT-6-12-X Attenuator - Recycled Sound, Power Plug 6 / 12, -6dB or -12dB
The Power Plug 6 / 12 attenuator is a "must have" device for anyone that plays a tube amp. If you want to work your power tubes without ear-splitting volume, you need an attenuator. The Power Plug is the BEST attenuator made for amps 50 watts and less. Simple 2 switch operation for -6db or -12db attenuation. Get your best tone!
Why 6/12? Engage 1 switch and remove -6db of power. Engage the 2nd switch and you're -12db. That's a volume reduction of 60%. The Recycled Sound attenuator is a passive, resistive load with compensated impedance and EQ, which maintains the designated impedance, EQ'd such that no degradation in tone is noted, even at full -12db attenuation. Use it as a Master Volume, use it to save your hearing at practice, find your tube tone without getting thrown out of the club, use it to prevent blowing up your vintage or low power speakers.
Use TWO in series and achieve -24db attenuation - bedroom level!
$89.95
M-K020 Power Supply - 4.5V, 500mA, Center Positive, for Korg PX4, PXR4
KA-193 wallwart power supply. For use with PX4, PX4B and PXR4.
  • Voltage: 4.5VDC
  • Current: 500mA
  • Tip positive; Sleeve negative
$9.45
M-K050 Power Supply - Korg, 9V, 500mA~1.2A, Center Negative
For use with MS2000, microKONTROL, microKORG, Etribes, DT7, AX1G/B, AX100G, AX1500, GT12, OT12, and PX3/3B.
$10.95
M-K080 Power Supply - Korg, 12V, 1500mA, Center Positive
Korg Power Supply, KA-310 adapter for X50, MicroX, R3, MR1000, or SP170. Please note that this requires an S-W128 AC power cord to connect to an AC wall outlet.
$29.95
M-PAS-S Power Supply - Power All System, 9V, 2000mA, for Effects Pedals
The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.
$19.95
P-ECB-002 Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
  • Voltage: 9VDC
  • Current: 200mA
  • Tip positive; Sleeve negative
$12.50
P-ECB-003 Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative

Dunlop ECB003 US wallwart power supply. Barrel connector.

  • Voltage: 9VDC
  • Current: 200mA
  • Tip Negative; Sleeve positive
$12.50
P-G00X Grommet - Rubber, for chassis holes
Package of 5
Listed diameter is inside diameter. Sold in packs of 5.
  • 3/8" diameter designed for chassis hole with diameter 1/2"
  • 1/8" diameter designed for chassis hole with diameter 1/4"
  • 3/16" diameter designed for chassis hole with diameter 5/16"
  • 1/4", small cutout diameter designed for chassis hole with diameter 7/16"
  • 1/4" diameter designed for chassis hole with diameter 7/16"
  • 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $0.95
P-H11-406 Strain Relief - Nylon, 0.12" x 0.22" Wire (SPT-1)
Two conductor, nylon, .12" x .22" wire (SPT-1). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points.
$0.50
P-H1200 Strain Relief - for ¾" x ~\frac{27}{32}~" hole, ~\frac{5}{16}~" cord diameter
16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
$0.85
P-H1300 Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter
For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
$0.95
P-HFAN Fan - 115V, AC ~\frac{50}{60}~ Hz, 1 Phase, low noise
Super low noise 115V-AC. Dimensions are 4 11/16" (height) x 4 11/16" (width) x 1 ½" (depth). The distance between mounting centers is 4 1/8" x 4 1/8".
$27.95
P-HFAN-GUARD Fan Guard - Metal Grill, Finger Guard
Metal finger-protecting guard for P-HFAN.
$3.25
On Backorder
P-SP2-106 Receptacle - IEC C14, for power cord, 3 prong
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$1.75
P-SP2-500 Receptacle - AC, Mates with S-W123 & S-W124 with Fuse Holder
I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses
$1.85
S-H200 Fuse Holder - for Marshall, ¼" Fuses
Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:
  • Rated current: 10A
  • Rated voltage: 250V AC
  • Contact resistance: 2MΩ @ 250V DC or less
  • Dialectric withstand: 1 minute @ 1500V AC
  • Insulation resistance: 100MΩ or more @ 500V DC
$4.65
S-H201 Fuse Holder - for Fender®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
  • Fits ½" chassis hole diameter
  • Mounted by Nut
$1.95
S-H203 Fuse Holder Cap - Peavey, top-slotted for screwdriver
Peavey cap for fuse holder. 1 1/16" length x 3/8" diameter. Top slotted for flat head screwdriver.
$3.85
S-H204 Fuse Holder Cap - Marshall, for 900 Series
Fuse holder cap for Marshall™ 900 series amps. Measures 5/8" in length.
$3.50
S-H205 Fuse Holder - 3AG-Type, High Quality
High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
$2.06
Don't see what you're looking for? Send us your product suggestions!