Power Supplies & Accessories

Black nylon AC power entry connector with the same mounting dimensions as the original Bulgin “Pignose” connectors used on early Marshall amps. This connector allows the amp to be fitted with a safer connector with no modifications to the chassis. Mounting hardware not included.

Prewired AA battery holder. This plastic battery holder fits two AA batteries. The six inch leads are prestripped and tinned stranded wire for an easy installation.

Open frame fuse block for GMA or GMD 5×20mm size fuses with a low profile design that features solder terminals made of tin plated brass. A unique design feature provides self-alignment of the clips to the fuse caps. This feature, plus a one-piece clip/terminal design, assures low contact resistance.

Peavey cap for fuse holder. 1 1/16" length x 3/8" diameter. Top slotted for flat head screwdriver.

Fuse holder cap for the fuse holder found on the Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. This cap fits 3AG fuses and pairs with S-H211.

High quality insulation cover for IEC C14 AC Power inlets. The cover is made of a thick durable PVC and fits most standard C14 type power inlets. The wire sleeve can be cut to securely fit over any standard wire gauge providing a fully insulated AC inlet.

Included in the PA-9ECB Basic Kit and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.

Replacement board for Marshall JCM 2000 DSL 100 amplifiers which frequently have issues with original boards. This replacement can bring your amp back to life!

Dunlop ECB003 US wallwart power supply. Barrel connector.

• Voltage: 9VDC
• Current: 200mA
• Tip Negative; Sleeve positive

Though-hole PCB mount fuse holder used on many Marshall amps such as the 900 series and some 2000 series amps. The fuse cap is sold separately as S-H204. Fits GMA and GMD 5×20mm fuses.

Fuse holder cap replacement for P-SP2-500 power receptacle.

Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.

Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a ⅛" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the ECO-Dapter® itself.

Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.

Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.

Prewired AA battery holder. This plastic battery holder fits a single AA battery and is a great option for vintage fuzz pedals that run on 1.5V, such as the Maestro FZ-1A.

Though-hole PCB mount fuse holder used on many Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. Check footprint and dimensions for compatibility. This holder fits 3AG fuses and pairs with the S-H212 cap. Cap sold separately.

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Note: The spade lugs have a detent rather than a hole.

Included in the PA-9ECB Basic Kit, PA-9ECD Deluxe Kit, and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.

Super low noise 115V-AC. Dimensions are 4 11/16" (height) x 4 11/16" (width) x 1 ½" (depth). The distance between mounting centers is 4 1/8" x 4 1/8".

Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Black/R allows the user to power over-sized effect units or units w/AC jacks in hard-to-reach places off of the Power-All Daisy Chain. The Cable-Black can be connected to any plug on any Power-All daisy chain, or directly to the ECO-Dapter® itself.

Marshall replacement power board.
Works in the following models:

• AVT50
• AVT100
• AVT150H
• AVT150
• AVT275
• AVT275X

High quality insulation cover for panel mount fuse holders. The cover is made of a thick durable PVC and fits many fuse holders. The wire sleeve can securely fit over any standard wire gauge used with fuse holders providing a fully insulated fuse connection.
Features

• Provides insulation against shock on rear of fuse holder
• PVC
• UL94V-0 rated flame retardant material

Fits S-H205

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects. Power-All® kits include a variety of useful cables for powering multiple pedals to the ECO-Dapter® 9V supply.