Power Supplies & Accessories

Detachable 3 conductor power cord for United Kingdom wall outlets. Cord end is IEC connected. GTSA-3 (Marshall™ type) 18 AWG. 2-1/2 meters (about 8 feet) length, 1/4” outer diameter.
$2.79
Save 20%
Originally: $3.50

For use with MS2000, microKONTROL, microKORG, Etribes, DT7, AX1G/B, AX100G, AX1500, GT12, OT12, and PX3/3B.
$10.95

Korg Power Supply, KA-310 adapter for X50, MicroX, R3, MR1000, or SP170. Please note that this requires an S-W128 AC power cord to connect to an AC wall outlet.
$29.95

AC power cord for the Korg KA-310 power adapter (part number M-K080).
This power cord features a standard IEC C7 non-polarized connector that mates with IEC C8 connectors. These are sometimes referred to as "figure 8" or "shotgun" connectors.
This power cord features a standard IEC C7 non-polarized connector that mates with IEC C8 connectors. These are sometimes referred to as "figure 8" or "shotgun" connectors.
$9.95

The Power Plug Lite offers up to -10db attenuation in a rotary switch with -2db increments. The Power Plug Lite will accept all impedances and is rated for up to 50 watt amps. The same cool extruded aluminum case as the original Power Plug (M-ATT-6-12) for those who want a lighter touch and more control. Turn your tube amp UP to drive your power tubes. This is where tube amps blossom and where players get in trouble. Use the attenuator to drop your overall volume to more tolerable levels. You can dial in your breakup, which may be too loud, then attenuate to lower the overall volume.
$114.95

The Power Plug 100 offers the same -10db as the Power Plug Lite (M-PPLITE) but adds another "Bedroom Level" pot for further attenuation of up to -30dB AND is suitable for amps up to 100 watts! Turn your tube amp UP to drive your power tubes. This is where tube amps blossom and where players get in trouble. Use the attenuator to drop your overall volume to more tolerable levels. You can dial in your breakup, which may be too loud, then attenuate to lower the overall volume. So you can adjust your amp as usual and use the attenuator as an overall Master volume.
$189.95

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
$0.85

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$1.75

High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
$1.95

Three conductor, 8 or 12 foot detachable power cord with IEC female end SVT (Marshall type), 18 awg.
Starting at $4.95

Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
$3.10

Nylon cable clamp with room for 1/4” cable outer diameter. Perfect for securing cables to cabinet walls. For larger ½” cable clamps see P-HCABLECLAMP-10.
$0.15