Power Supplies & Accessories

S-W118 Cord - Replacement Black, Non-Polarized
Black SPT-1 power cable
  • non-polarized
  • tinned leads
  • 6 foot length
  • 18 AWG.
$2.44
S-H259 Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
$3.10
S-W104 Cord - Replacement Brown, Polarized Plug
Brown SPT-1 power cable
  • polarized
  • tinned leads
  • 6 foot length
  • 18 AWG
$2.95
P-SP2-800 Receptacle - IEC C14, Snap-in Panel Mount
High quality snap-in IEC C14 power entry connector. The connector is easy to install and is rated for 250VAC at 15A. The quick disconnect terminals can also be directly soldered to. Features:
  • High quality thermoplastic housing
  • Copper alloy terminals (4.8mm width)
  • Quick installation
  • Fits 0.8mm to 2mm thick panels
$2.29
P-JB-SM-S Power Jack - DC Panel Mount, Vintage Boss Style, 5.5mm External, 2.1mm Internal
This DC power jack is similar to those used on vintage MIJ Boss pedals and others. This jack has a 2.1mm pin for use with 5.5mm barrel plugs. Three solder lugs are available for tip, ring, and switch.
$0.64
S-H219 Fuse Holder - 3AG-Type, Low Profile, Knob, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile bayonet style knob and reduced overall height. The connector at the end of the holder is right angled which reduces the internal depth as well. It is a similar style to fuse holders used on many Fender® amps. Mounting nut and rubber washer included.
$5.95
P-BATC-SN-1F Battery Clip - Vintage Style, 9 Volt, Fiberboard Frame
9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.
$1.20
S-H158 Battery Holder - 9V, Chassis Mount, Horizontal
High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited.
$1.25
P-H1200 Strain Relief - for ¾" x ~\frac{27}{32}~" hole, ~\frac{5}{16}~" cord diameter
16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
$1.29
P-JB-EN-S Power Jack - DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.
$0.64
S-9V-GCELL Battery - 9V, Carbon Zinc, GP, Greencell, Extra Heavy Duty
Extra heavy duty carbon zinc batteries from GP. The GP Greencell 9V is a favorite for fuzz pedals and is the stock battery for many boutique builders such as D*A*M and others. Additionally, these batteries are a great choice for any low current battery powered pedal or other devices.
$3.25
P-JB-PC-S Power Jack - DC PC Mount, 5.5mm External, 2.1mm Internal
This PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.
$0.64
S-H215 Fuse Holder - Clip, GMA-Type, PCB Mount
Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.
$0.39
S-H159 Battery Holder - 9V, Chassis Mount, Vertical
High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The vertical mount and small footprint of the holder are great for narrow spaces and work well for any project. See S-H158 for horizontal-mount.
$1.25
S-H220 Fuse Holder - 3AG-Type, Low Profile, Slotted, Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.
$3.25
S-H210 Fuse Holder - 3AG-Type, Tweed Style, Solder Lug
Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
$4.70
P-HTIEMOUNT-X Cable Tie Mount - Nylon, Adhesive Backing
Colors Available:
Nylon cable tie mounts with adhesive backing. These mounts easily attach to most surfaces using a strong foam adhesive. Zip ties can be fed through the openings on the mount to secure wires to an enclosure, board, or any other convenient location.
Starting at $1.50
package of 5
S-H200 Fuse Holder - for Marshall, ¼" Fuses
Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:
  • Rated current: 10A
  • Rated voltage: 250V AC
  • Contact resistance: 2MΩ @ 250V DC or less
  • Dialectric withstand: 1 minute @ 1500V AC
  • Insulation resistance: 100MΩ or more @ 500V DC
$5.99
P-JBCL-PC-S-X Power Jack - Cliff, DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Colors Available:
High quality PCB mounted DC jack made by Cliff. This style of PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.
Starting at $1.79
P-SP2-500 Receptacle - AC with Fuse Holder, mates with S-W123 & S-W124
I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses
$1.85
P-BATC-SN-1S Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style
Premium 9V battery clip with a rigid plastic frame. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.15
S-H216 Receptacle - IEC C14, Panel Mount, Fuse Holder, 10A, 250VAC
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. This receptacle features a built-in fuse holder for 5mm x 20mm fuses. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$4.89
P-PC-INV-SWITCH PCB - Charge Pump, -9V from +9V, 3PDT Switch Mount
3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.60
S-W142 Cord - Power, 18 AWG, 3 Conductor, SVT, 6 ft, Gray
18AWG SVT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. SVT cords have a thinner insulation than SJT cords. This version comes in gray to pair with vintage style amps and equipment.
$6.95
Don't see what you're looking for? Send us your product suggestions!