Power Supplies & Accessories

Black nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables. See P-HCABLECLAMP-X for white nylon versions of these clamps.

Large rubber grommet for mounting footswitches on FZ-1 and FZ-1A style builds. Requires a 0.812” (20.6mm) mounting hole. This grommet’s 0.5” (12.7mm) inner diameter fits most common footswitches. These are great for replacing originals, replica builds of these Maestro pedals or for general sound damping on footswitches.

Black SPT-1 power cable

• non-polarized
• tinned leads
• 6 foot length
• 18 AWG.

Black nylon AC power entry connector with the same mounting dimensions as the original Bulgin “Pignose” connectors used on early Marshall amps. This connector allows the amp to be fitted with a safer connector with no modifications to the chassis. Mounting hardware not included.

½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.

Dunlop ECB003 US wallwart power supply. Barrel connector.

• Voltage: 9VDC
• Current: 200mA
• Tip Negative; Sleeve positive

Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects. Power-All® kits include a variety of useful cables for powering multiple pedals to the ECO-Dapter® 9V supply.

9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.

Power Cord / cable - (3 conductor) Bare End, 16 AWG

Durable nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features

• Approved for outdoor use.
• UL Listed 6.6 nylon.
• Locks tightly - Won’t stretch or slide.
• Temperature range from 40° to 180°F.

This PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.

Listed diameter is inside diameter. Sold in packs of 5.

• 3/8" diameter designed for chassis hole with diameter 1/2"
• 1/8" diameter designed for chassis hole with diameter 1/4"
• 3/16" diameter designed for chassis hole with diameter 5/16"
• 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
• 1/4" diameter designed for chassis hole with diameter 7/16"
• 5/16" diameter designed for chassis hole with diameter 7/16"

Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the Power-All® ECO-Dapter® 9 VDC power supply to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices (actual number of units depends on current draw of individual units used).

High quality PCB mounted DC jack made by Cliff. This style of PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.

Cable-mounted inline switch (On-Off) most often used for lamps and other applications. This switch pairs with SPT-1 type power cords and features a thumbwheel actuator.

A new two-prong plug, acceptable as a retro or vintage substitute. The plug easily accepts our twisted 18 and 16 gauge wires (two-conductor only). Wire Opening Diameter: 11.2 mm x 8.4 mm, 7/16" x 5/16" UL Rating: 15A-125V Made in Mexico

Heavy duty mil-spec barrel plug from Switchcraft. The S10 is a high current, non-sealed power jack with a similar design as the ¼” jacks from Switchcraft. The plug is rated for up to 11A of current.

For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.

• Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
• Securely anchors, insulates, and protects cables at panel entry points

Fuse holder cap for the fuse holder found on the Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. This cap fits 3AG fuses and pairs with S-H211.

Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Black/R allows the user to power over-sized effect units or units w/AC jacks in hard-to-reach places off of the Power-All Daisy Chain. The Cable-Black can be connected to any plug on any Power-All daisy chain, or directly to the ECO-Dapter® itself.

Metal frame AA battery holder. This battery holder fits two AA batteries and is a great option for electronics that run on 3V. It features two solder lugs for connecting wires to the positive and negative ends. The battery holder in the original FZ-1 fuzz pedals looks nearly identical to this holder.

Genuine Cliff barrel plug for use with 5.5mm / 2.1mm barrel jacks. This plug is great for repairing power supplies and making cables. The outside housing is made of a thick durable plastic.