Potentiometers
Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.Check out our Tech Corder articles on pots, including Potentiometer Types.

Genuine Dunlop replacement potentiometer for Dunlop/ MXR pedals. PC mount, 47K audio taper, knurled shaft.
$2.95

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.
$22.95

Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100 kΩ. Original Dunlop replacement part. The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.
$20.59

Custom taper 20k Dunlop potentiometer used in 105Q Crybaby Bass Wah. 1 million cycles, maintenance free.
$22.95

250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.
$19.95

Genuine Dunlop replacement fuzz potentiometer for JDF2 Fuzz Face. 1 kΩ, linear, solid plastic shaft. Made In U.K.
$4.95

Genuine Dunlop replacement potentiometer for Jimi Hendrix JH-F1 Fuzz Face. 470 kΩ, Audio taper, solid plastic shaft. Made In U.K.
$5.95

Genuine Dunlop replacement potentiometer for wah/volume.
- 10 kΩ Linear
- Gear included
$14.40

Black dust cover for use with 16mm or 24mm potentiometers. These covers slide over the back of the pot covering the holes and gaps to help prevent dust from accumulating inside avoiding potential repairs and replacing down the road. The dust cover is made of a soft rubbery material and is easy to install on standard 24mm and 16mm pots.
Starting at $0.85

CTS 10K linear bias potentiometer. This panel mount trimpot is used in many Fender® amplifiers.
Please note: This potentiometer does not include the washer and nut. If you would like to purchase the washer and nut, see our part number R-VNUT-38
Please note: This potentiometer does not include the washer and nut. If you would like to purchase the washer and nut, see our part number R-VNUT-38
$2.95

1M ohm, Solid Shaft. Original Fender. Used for Volume and Tone control in many Fender guitars as well as amplifiers.
$6.25

Genuine Fender® 250K pan pot with center detent. Pan pots are also known as balance pots. Solid shaft with 3/8” bushing. Mounting hardware not included. See R-VNUT-38 for a compatible nut and washer.
$5.65

250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.
$12.95

250K ohm, audio taper. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging.
$6.75

250K ohm. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging. Some Fender guitars have a unique tone circuit that features a "Delta Tone' Control. The "Delta Tone' system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors.
$6.95

250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender® packaging.
$5.75

250K ohm, solid shaft, no load. Some Fender guitars have a unique tone circuit that features a "Delta Tone" Control. The "Delta Tone" system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which has a detent at the 5 position and gradually reduces the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup.
$6.95

Original Fender solid shaft 250K potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.
$7.50

24mm, solder lug potentiometers with 10% resistance tolerance. These ⅜” bushing pots have an audio taper and the solid shaft fits 6.35mm (¼”) knobs.
For linear taper versions, see R-V38-10TOL-XL.
For linear taper versions, see R-V38-10TOL-XL.
$2.95

24mm, solder lug potentiometers with 10% resistance tolerance. These ⅜” bushing pots have a linear taper and the solid shaft fits 6.35mm (¼”) knobs. For audio taper versions, see R-V38-10TOL-XA.
$2.95

Alpha Dual Potentiometer Shaft Width: ¼" Shaft Length: 5/16" Bushing Diameter: ⅜" Bushing Length: ¼" Body Diameter: 24mm Body Height: 20mm Rotation: 300° Wattage Rating: 0.25w Voltage Rating: 250v Conductive Material: Carbon Composition
$3.45