Pedal Parts / DIY

C-BC-X Capacitor - Vishay BC, Aluminum Electrolytic, 021 ASM Series, Axial Lead
High quality axial-leaded electrolytic capacitors. These 021 ASM series capacitors are produced by Vishay BC, formerly known as Philips / BC. These capacitors have been produced for many years and can be found in a wide variety of music equipment ranging from vintage amps by Vox and Marshall to classic fuzz pedals such as the Fuzz Face and Tonebender. Suggested applications include general purpose use, industrial, automotive, audio-video, coupling, decoupling, smoothing, filtering, buffering, portable and mobile equipment. Features
  • Long useful life: 2500 h to 8000 h at 85 °C
  • Miniaturized, high CV-product per unit volume
  • Charge and discharge proof
  • Polarized aluminum electrolytic capacitors, non-solid electrolyte
  • Axial leads, cylindrical aluminum case, insulated with a blue sleeve
Starting at $1.75
C-FFD01-250 Capacitor - 0.01µF, 250V, Chicklet style, Axial Lead
Flat 0.01uF (10nF) film capacitor rated for 250V. Made of metallized polypropylene film, this capacitor is a great choice for audio applications. The style of this yellow capacitor is similar in appearance to the flat rectangular Philips 341 output caps found in original Fuzz Face pedals.
$1.35
C-PH-RMST-D015 Capacitor - Philips, KT-347, 400V, .015uF, Polyester Film
New old stock radial capacitors from Philips with 10mm lead spacing. The KT-347 series capacitors feature the same lacquer coating as the Mullard / Philips mustard caps found in classic Marshall amps and many vintage pedals. These NOS caps feature a low-inductive wound cell of metal foil and a polyethylene terephthalate film.
$2.25
C-SI-RF-D1 Capacitor - Siemens, 250V, .1uF, Film
New old stock radial capacitors from Siemens with 10mm lead spacing. These 0.1uF film capacitors are rated for 250V. The construction matches the style found in vintage equipment such as the MKIII and MKIV Tone Bender pedals.
$5.95
C-SI-RF-D22 Capacitor - Siemens, 250V, .22uF, Film
New old stock radial capacitors from Siemens with 10mm lead spacing. These 0.22uF film capacitors are rated for 250V. The construction matches the style found in vintage equipment such as the MKIII and MKIV Tone Bender pedals.
$5.95
K-P155 Battery Clip - 9 Volt with Vinyl Tab
Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.
$0.50
P-1361-2 Terminal Pin - PCB Mount, 0.05” Diameter, 0.25” Length
PCB mount terminal pin made of tinned brass. This pin fits 0.064” mounting holes and can be swage or solder mounted. The pin diameter is 0.05” and has a total length of 0.25” when mounted. Great for connecting offboard wiring by soldering directly to the pin or using an appropriate connector.
$0.79
P-BATC-SN-1F Battery Clip - Vintage Style, 9 Volt, Fiberboard Frame
9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.
$1.20
P-BATC-SN-1S Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style
Premium 9V battery clip with a rigid plastic frame. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.15
P-BATC-SN-1T Battery Clip - Premium, 9 Volt, Rigid Frame, I-Style
Premium 9V battery clip with a rigid plastic frame and I-style wire orientation. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.20
P-BATC-SN-3S Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style, Shielded Eyelets
Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.15
P-ECB-229 Knob - Dunlop, Jimi Hendrix Fuzz Face JH-F1
Genuine Dunlop replacement knob for Jimi Hendrix JH-F1 Fuzz Face. Knob is designed for use with solid/plastic 1/4” shafts and features set screw attachment. Two washers are included.
$7.65
P-ECB-244 Battery Box - Dunlop, snap-in enclosure
Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.
$2.50
P-ECB-253 Potentiometer - Dunlop, 1 kΩ FUZZ for the JDF2 Fuzzface
Genuine Dunlop replacement fuzz potentiometer for JDF2 Fuzz Face. 1 kΩ, linear, solid plastic shaft. Made In U.K.
$7.95
P-ECB-255 Potentiometer - Dunlop, 470K kΩ for JH-F1 Jimi Hendrix Fuzzface
Genuine Dunlop replacement potentiometer for Jimi Hendrix JH-F1 Fuzz Face. 470 kΩ, Audio taper, solid plastic shaft. Made In U.K.
$9.95
P-ECB-9V1A Battery Box - Gotoh, BB-04, Single, 9 volt
Single 9 volt battery box. See P-ECB-9V1B for single battery box with removable adapter. See P-ECB-9V2 for double battery box.
$14.95
P-ECB-9V1B Battery Box - Gotoh, BB-02, Single, 9 volt, with removable adapter
Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.
$14.95
P-ECB-9V2 Battery Box - Gotoh, BB-04W, Dual, for 9 volt batteries
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.95
P-GROM-FZ1 Grommet - Rubber, for FZ-1 Style Footswitch Mounting
Large rubber grommet for mounting footswitches on FZ-1 and FZ-1A style builds. Requires a 0.812” (20.6mm) mounting hole. This grommet’s 0.5” (12.7mm) inner diameter fits most common footswitches. These are great for replacing originals, replica builds of these Maestro pedals or for general sound damping on footswitches.
$0.79
P-H-YY-HMT-BLU Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66", Hammered Blue
Limited Run!
YY enclosure finished in a hammered blue powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
  • Vintage style slant
  • Hammered blue powdercoat
  • Flat top-section for mounting controls
  • Recessed lid
  • Thick diecast construction

Part of a limited run of hammered blue enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BLU 1590N1 / 125B P-H1590N1CE-HMT-BLU 1590N1 (Gorva) P-H1590N1-GORVA-HMT-BLU 1590BB (Gorva) P-H1590BB-GORVA-HMT-BLU YY P-H-YY-HMT-BLU 1590TRPD Trapezoid P-H1590TRPB-HMT-BLU
$35.95
Out of Stock
P-H-YY-HMT-BRZ Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66", Hammered Bronze
Limited Run!
YY enclosure finished in a hammered bronze powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
  • Vintage style slant
  • Hammered bronze powdercoat
  • Flat top-section for mounting controls
  • Recessed lid
  • Thick diecast construction

Part of a limited run of hammered bronze enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BRZ 1590N1 / 125B P-H1590N1CE-HMT-BRZ 1590BB P-H1590BBCE-HTM-BRZ YY P-H-YY-HMT-BRZ 1590J P-H1590J-HMT-BRZ
$28.95
Out of Stock
P-H-YY-HMT-GN Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66", Hammered Green
Limited Run!
YY enclosure finished in a hammered green powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
  • Vintage style slant
  • Hammered green powdercoat
  • Flat top-section for mounting controls
  • Recessed lid
  • Thick diecast construction

Part of a limited run of hammered green enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-GN 1590N1/125 P-H1590N1CE-HMT-GN 1590BB P-H1590BBCE-HMT-GN YY P-H-YY-HMT-GN
$28.95
Out of Stock
P-H-YY-HMT-S Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66", Hammered Silver
Limited Run!
YY enclosure finished in a hammered silver powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
  • Vintage style slant
  • Hammered silver powdercoat
  • Flat top-section for mounting controls
  • Recessed lid
  • Thick diecast construction
$27.95
Out of Stock
P-H-YY-X Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66"
Colors Available:
Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
  • Vintage style slant
  • Flat top-section for mounting controls
  • Recessed lid
  • Thick diecast construction
Starting at $23.95
Don't see what you're looking for? Send us your product suggestions!