Pedal Parts / DIY

P-Q-AS394H Transistor - AS394H, Matched Pair, Alfa, TO5-8 case, NPN
The AS394H is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.
$4.25
P-PC-ST1 StripBoard - Single Sided, 3.15” x 1.97”, Mounting Holes
Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.
$3.09
P-ECB-555 Switch - Dunlop, Footswitch, DPDT, Solder Lugs, for MXR
Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR, Cry Baby, and other effects pedals.
$14.95
P-Q2N2646 Transistor - 2N2646 Programmable Unijunction
2N2646 programmable unijunction transistor often referred to as a PUT. The 2N2646 can be found in many tremolo effects pedal projects and vintage classics such as the Vox Repeat Percussion.
$2.65
P-QLM3900 Op-Amp - LM3900, Quad, Norton, 14-Pin DIP
LM3900 quad op amp in a 14-pin DIP package. These devices consist of four independent, high-gain frequency-compensated Norton operational amplifiers that were designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies is also possible. The low supply current drain is essentially independent of the magnitude of the supply voltage. These devices provide wide band- width and large output voltage swing. Features
  • Wide Range of Supply Voltages, Single or Dual Supplies
  • Wide Bandwidth
  • Large Output Voltage Swing
  • Output Short-Circuit Protection
  • Internal Frequency Compensation
  • Low Input Bias Current
  • Designed to Be Interchangeable With National Semiconductor LM2900 and LM3900, Respectively
$0.65
P-Q1N5817 Diode - 1N5817, Schottky, High Switching Speed
Schottky diode with low forward voltage drop and high switching speeds.
$0.20
P-TC4-1 Terminal Strip - Ceramic, 1 row, 4 slots, 2.5mm thread
Ceramic terminal strip, 1 row, 4 slots, 2.5mm thread.
$3.29
P-QCD4049 CMOS - CD4049, Hex Inverting Buffer and Converter, 16-Pin DIP
The CD4049UB devices are inverting hex buffers, and feature logic-level conversion using only one supply voltage (VCC). The input-signal high level (VIH) can exceed the VCC supply voltage when these devices are used for logic level conversions. These devices are intended for use as CMOS to DTL or TTL converters and can drive directly two DTL or TTL loads. (VCC = 5 V, VOL ≤ 0.4 V, and IOL ≥ 3.3 mA.) Features:
  • Inverting
  • High Sink Current for Driving 2 TTL Loads
  • High-to-Low Level Logic Conversion
  • 100% Tested for Quiescent Current at 20 V
  • Maximum Input Current of 1 µA at 18 V Over Full
  • Package Temperature Range; 100 nA at 18 V and 25°C
  • 5-V, 10-V, and 15-V Parametric Ratings

Applications
  • CMOS to DTL or TTL Hex Converters
  • CMOS Current Sink or Source Drivers
  • CMOS High-to-Low Logic Level Converters
$0.75
P-Q2N3392 Transistor - 2N3392, Silicon, TO-92 case, NPN
The 2N3392 is a general purpose NPN transistor in a TO-92 case. The 2N3392 is used in some original silicon Fuzz Face pedals as well as the Brassmaster fuzz.
$0.39
R-VSHL-BX Potentiometer - Song Huei, Linear, 9mm, Tall
Linear taper, vertical mount, Song Huei pots with a 6mm shaft. These 9mm pots are popular in DIY guitar pedals, modular synthesizers, and other projects where space is limited. The knurled shaft features a painted indicator line so no knob is required. These tall versions have a 17mm shaft length and a total height of 25mm. For audio taper versions, see R-VSHL-AX. For center notched linear taper versions, see R-VSHL-BX-CN.
$0.95
C-D-100V Capacitor - 100V, Ceramic Disc, ± 10%
100 V ceramic disc capacitors. ± 10% tolerance.
Starting at $0.25
P-H-ST8202 Footswitch - ST Professional, DPST, Latching, Solder Lugs
Heavy duty DPST latching switch made in Italy by ST Professional. The body is made of PBT that is riveted to the bushing plate for a sturdy construction. The actuation force is lighter than similar Carling switches and provides tactile and audible feedback so the switching action is apparent to the user. This version features standard solder lugs. This style of footswitch is similar to the vintage footswitches found in the Gary Hurst Fuzz King, the Hornby Skewes Shatterbox, the Jen Fuzz III, the Selmer Buzz Tone, and others.
$9.95
P-Q24LC32AP Integrated Circuit - 24LC32A/P, EEPROM, 8-pin DIP
24LC32A/P EEPROM in an 8-pin DIP package commonly used in Spin FV-1 projects. The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced, low power applications such as personal communications or data acquisition. The 24LC32A also has a page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range make this device ideal for low-power/low-voltage, nonvolatile code and data applications.
$1.29
P-HTOG-GORVA-S1 Switch - GØRVA, Submini Toggle, SPDT, 2 Position, PC Pins, Medium Bat
Premium two position SPDT submini toggle switches from Gorva Design. The Bascular Sub Mini switches have a medium 7.37mm actuator length. These switches feature silver plated copper alloy contacts. The bushing is smooth and the switch is secured with the mounting bracket on the PCB. RoHS compliant & lead-free. Details
  • 5.59mm non-threaded bushing
  • 2-Position On/On
  • 4.95mm panel hole diameter
  • Single pole/Double throw (SPDT)
  • PC Pins

Features
  • Power Rating: DC9V, 1A
  • Contact Resistance: <20mΩ
  • Insulation Resistance: 1000MΩ Minimum
  • Dielectric Strength: 1000V RMS @ Sea Level
  • Operating Temperature: -40°C ~ +85°C
  • Electrical Life: 30,000 Cycles
  • RoHS & Lead-free
$1.35
P-H1590DD Chassis Box - Hammond, 1590DD, Diecast, 7.40" x 4.72" x 1.30"
Hammond Mfg. Diecast Aluminum Chassis Box – 7.4” x 4.7” x 1.3”. Made in Taiwan. Key Features: • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
$20.25
P-HROTO-1 Chassis - Three Knob Fuzz, Pressed Steel
Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for ⅜” jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.
  • Footswitch Hole Diameter: 0.492 in. (12.5mm)
  • Potentiometer Hole Diameter: 0.294 in. (7.47mm)
  • Jack Hole Diameter: 0.447 in. (11.35mm)
$19.95
P-H1550P Chassis Box - Hammond, 1550P, Diecast, 3.15” x 2.17” x 0.83”
The 1550P is a 3.15 in. x 2.17 in. x 0.83. diecast enclosure made by Hammond. This enclosure is a great option for extra compact builds while still offering plenty of room for an easy construction.
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.
  • M3.5-0.6 threaded holes for mounting the bottom plate. Screws included.
$7.75
P-H5418 Switch - Carling, Mini Toggle, SPDT, 2 Position, Solder Lugs, Flattened
Carling mini-toggle switch, SPDT. This switch features a flattened actuator.
  • 0.354" bushing length
  • 2-Position On/On
  • ¼" mounting hole diameter
  • Single pole/Double throw (SPDT)
  • Solder Lugs
$5.45
C-PEI Capacitor - 100V, Polyester Film Inductive
Polyester film dielectric, aluminum foil electrode, copperply leads and epoxy resin coating in inductive type.
  • Small size, light weight and low cost
  • Dissipation factor is small because the leads are directly welded to electrodes
  • Epoxy resin vacuum-dipped enhances the mechanical strength, humidity resistance
  • 100 volt rating
  • Operating temperature range: -40°C to +85°C.
  • Package of 5
Starting at $0.40
package of 5
P-LBL-BUILD-2 Label - Quality Assurance, Vintage Style Sticker
Vintage style quality assurance label. This label has an electronic test line for the name of a technician responsible for testing the electronics and a sound test line for the name of a technician responsible for testing the functionality of the device. This sticker is a great way to document quality assurance testing with a professional presentation on the chassis of a pedal or amp.
$1.95
S-MHS-ASST-2 Heat Shrink - Assorted Diameters, 2.5" Long, 158 Pieces
2 to 1 heat shrink tubing variety pack. This pack includes six different diameters ranging from 1/16” to 1/2”. Each piece is 2.5” in length. This set comes in a hard plastic case perfect for sorting and storing heat shrink. Features:
  • Resistant to common fluids and solvents
  • UL and CSA listed
  • UV resistant
  • Meets DEF. STAN 59.97
  • Meets UL 224, 125°C and CSA C22.2 No. 198.1
  • Meets MIL-DTL-23053/5 Class 2 & 3
  • Flame retardant (Does not include transparent)
  • Seals and protects cable splices and terminations.
  • Thin wall tubing
$12.35
W-SC-DRESS-X Nut - Switchcraft, Dress Nut / Sealing Nut, ⅜”-32 UNEF-2A
Switchcraft shouldered hex nuts for ⅜”-32 UNEF-2A threaded bushings. These nuts include a rubber grommet for use in sealed systems and also add a unique look to any build such as pedals or amplifiers. The large nut (W-SC-DRESS-1) is intended for panel or chassis thicknesses of 0.05” through 0.09”. The small nut (W-SC-DRESS-2) is intended for panel or chassis thicknesses of 0.095” through 0.125”. Rubber grommet included.
Starting at $2.49
R-VAMA-SS-PCL Potentiometer - Alpha, Audio, Solid Shaft, Right Angle, 16mm
Alpha Mini Pots with solid shaft and long PC mount terminals.
  • Threading: M7 x 0.75
  • Distance between terminals: 5 mm (0.197”)
  • Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
  • Lead Distance from shaft center: 16 mm (0.630”)
  • Lead Thickness: 0.5 mm (0.020”)
$1.25
P-ECB-002 Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
  • Voltage: 9VDC
  • Current: 200mA
  • Tip positive; Sleeve negative
$13.45
Don't see what you're looking for? Send us your product suggestions!