Pedal Parts / DIY

12 ½" mm, stereo, insulated, PC mount, bushing length = 0.29".

TS jack for Peavey with a switched tip connection. This jack features an additional tip connection used in some Peavey amps. 2 tip HID (High Definition), insulated, plastic bushing.

This nickel-plated brass adapter sleeve converts a 0.125 in. (3.17mm) shaft potentiometer to ¼" shaft (6.35mm), allowing for ¼" knobs to be used on a wider range of potentiometers. The cutout on the sleeve allows the set screw of the knob to secure directly to the shaft of the pot. Depending on the knob used, a longer set screw can be required.

Small 42TM022 audio transformers with a 1.5KΩ:600Ω impedance. This transformer is a popular choice for octavia style builds as well as ring modulators. The leads are soft metal wire and can be adjusted to fit a variety of applications. RoHS compliant. Rated for 200mW.

Large 5.709” x 3.37” x 1.933” Hammond 1590J enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

High-quality Bourns 3362P trimpots. These single-turn cermet trimmers can be found in countless guitar pedals and synthesizer modules. Sealed trimmers are built with an o-ring seal to prevent entrance of moisture and serve as a mechanical restraint to prevent unwanted wiper movement. ±10% tolerance.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.

PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 6.35mm horizontally and 22mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. 2x9 Board:

• 2 rows of 9 eyelets (18 total)
• 6.35mm x 22mm eyelet spacing
• 55.44mm x 26.66mm board
• 45mm spacing for 3.2mm mounting holes
• Great fit for 1590B and Gorva C65 enclosures

Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. These 1/8W resistors have a very small body and are great for tight builds.

The NJM2120 is a dual operational amplifier of 2-INPUT and 1-OUTPUT with analog switch. The NJM2120 can be used as analog switch under the condition of GV=0dB, as Switch + Amp in order that each gain (A or B) can be adjusted independently. Each amplifier of the NJM2120 has the same electrical characteristics as the NJM4558. The NJM2120 is suitable for audio, video, electrical musical instrument, etc.

Dual-gang 16mm potentiometers with a solid shaft and a linear taper. These pots have solder lug terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Bushing Length: 6.5mm (0.256")
• Shaft Diameter: 6.35mm ( 0.250")
• Taper: Linear

High quality crush-proof boxes that are perfectly sized for stompboxes. This cardboard box features triple wall sides and double wall front and bottom ensuring a safe housing for your pedals. The inside dimensions 7 ⅛” x 5” x 3" fit 1590XX, 1590X, and smaller sized pedals along with accessories such as power supplies or cables.. These boxes are ideal for storing or packaging effects pedals.
See S-B418 for boxes to fit 1590B, 1590G, 1590N1 / 125B enclosures.
See S-B430 for boxes to fit 1590BB, 1590N1 / 125B enclosures.

Holder for mounting LEDs to panels.

J201 N-Channel JFET in a TO-92 package. The J201 is designed primarily for low level audio and general purpose applications with high impedance signal sources.

• Max drain to gate voltage = 40 V
• Max gate to source voltage = -40 V
• Max forward gate current = 50 mA

The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.

Genuine Dunlop replacement housing screws for MXR/ Dunlop pedals. Replace lost screws and keep your battery access plate on tight. 6-32 thread, Phillips head.

TLC274 quad op amp in a 14-pin DIP package. The TLC274 quad operational amplifier combines a wide range of input offset voltage grades with low offset voltage drift, high input impedance, low noise, and speeds approaching that of general-purpose BiFET devices. These devices use Texas Instruments silicon- gate LinCMOSTM technology, which provides offset voltage stability far exceeding the stability available with conventional metal-gate processes. The extremely high input impedance, low bias currents, and high slew rates make these cost-effective devices ideal for applications which have previously been reserved for BiFET and NFET products.

Cliff S4 PC-A (L Leg). Stereo input jack, metal nut, 6 pin pc mount. Low-noise Ni-Ag® Alloy Self-Cleaning Contacts for superior performance and reliability Tough, molded grade 1 black Nylon body. Supplied with a black nylon hexagonal mounting nut. Designed to receive both mono and stereo ¼" jack plugs.

DPDT momentary footswitch. AC125V/4A AC250V/2A. Rated for 50,000 make-and-break cycles at full load.

Phenolic skirted knobs with a set screw and brass insert. These unique knobs closely match the RCA style of knobs used on vintage test equipment, radios, studio consoles and other equipment. They are sometimes referred to as fester knobs. The RCA style knobs feature an inlay indicator line. Fits ¼” (6.35mm) pot shafts. 22mm Skirt:

• Height: 0.495in. (12.6 mm)
• Diameter: 0.875 in. (22 mm)
• Fits ¼" shaft with set screw

26mm Skirt:

• Height: 0.656 in. (16.7 mm)
• Diameter: 1.02 in. (26 mm)
• Fits ¼" shaft with set screw

33mm Skirt:

• Height: 0.792 in. (20.1 mm)
• Diameter: 1.293 in. (33 mm)
• Fits ¼" shaft with set screw

40mm Skirt:

• Height: 0.865 in. (22 mm)
• Diameter: 1.568 in. (40 mm)
• Fits ¼" shaft with set screw

Dust cover for smaller low profile DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.

Included in the PA-9ECB Basic Kit and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.