Pedal Parts / DIY

P-ECB-152 Bottom Plate - Dunlop, for GCB-95 with Battery Door
Bottom Plate for GCB-95. Original Dunlop replacement part. Includes battery box, four mounting screws and four black rubber feet.
$14.25
P-H1032L Chassis Box - 1032L, Diecast, Looper, 10" x 2.75" x 1.89"
Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box. Add 0.16" to enclosure depth for lid.
$10.95
P-QNE5532 Op-Amp - NE5532, Dual, Low-Noise, 8-Pin DIP
This a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:
  • Operating Voltage = ±3V~±22V
  • Small Signal Bandwidth = 10MHz typ.
  • Output Drive Capability = 600Ω,10Vrms typ.
  • Input Noise Voltage = 5nV/√Hz typ.
  • Power Bandwidth = 140kHz typ.
  • Slew Rate = 8V/µs typ.
  • Bipolar Technology
$1.15
P-Q1N4937 Diode - Fast Recovery, 1A, 600V, 1N4937
A semiconductor device that, above a certain reverse voltage(the zener value) has a sudden rise in current. If forward biased, the diode is an ordinary rectifier. When reverse biased, it exhibits a sharp break in its current-voltage graph. Voltage across the diode remains essentially constant for any further increase of reverse current.
$0.20
M-PAS-CABLE-6 Cable - Power All, Grey Battery Snap Jumper
Included in the PA-9 Power-All System and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.
$3.00
R-VAV-AX Potentiometer - Alpha, Audio, 9mm, Vertical
Audio taper (log), vertical mount, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.
$1.85
P-H498-PC Footswitch - DPDT, PC Mount, latching
Latching DPDT footswitch, PC mount. Made in Taiwan.
$3.95
S-HS632-X Screw - 6-32, Phillips, Pan Head, Machine, Zinc
Package of 5
Phillips panhead machine screw, 6-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
$0.40
S-H172X Standoffs - #6-32, Female, Aluminum
Package of 4
#6-32 threading, package of 4. Comes in 1/2" or 3/4". For male to female standoffs, see S-H170X
$2.20
S-H532-A ¼" Jack - Stereo, PC Mount, metric threading
1/4" stereo jack. 3 PC mount terminals include: tip, ring and sleeve. Metric threading: M12 x 1.0.
$1.95
P-ECB-78 Potentiometer - Dunlop, Wah, 10 kΩ linear
Genuine Dunlop replacement potentiometer for wah/volume.
  • 10 kΩ Linear
  • Gear included
$14.50
W-SC-11G ¼" Jack - Switchcraft, Mono, Open Circuit, Gold Plated
Genuine Switchcraft Type 11 ¼” jack with complete gold plating. All metal parts are gold plated including the washer and nut.
$9.95
P-H1590CX Chassis Box - Hammond, 1590C, Diecast, 4.71" x 3.70" x 2.07"
Colors Available:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $11.32
S-H509 ¼" Jack - Fender®, Mono, for Amps 1999 to present
Fender R/A 1/4" mono jack. Used 1999-present. Hex nuts not included (S-H510).
$4.25
On Backorder
R-VM-NUT-2 Nut - M8x0.75 hex, for potentiometers / switches / jacks
Package of 5
M8 x 0.75 threaded hex nut. For use on potentiometers, switches, and jacks.
$1.25
P-H544 Switch - Carling, Mini Toggle, SPDT, On-On, PC Mount, right angle
Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:
  • SPDT ( Single Pole/ Double Throw) On-On switch
  • 0.275" bushing length
  • 0.270” bat length
  • ¼" chassis hole diameter
  • Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.
$2.50
P-0500H Terminal Strip - 5 Lug, 0 Common, Horizontal
Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.
$4.50
R-G Resistors - ⅛ Watt, Metal Film, 1% tolerance
Package of 5
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. These 1/8W resistors have a very small body and are great for tight builds.
$0.65
P-K428 Knob - Peavey, Black Pointer, White Line
Black pointer with white line. Fits a 3/16" knurled shafts. Push on Peavey part: 70902145
$3.95
W-RN-12B ¼" Jack - Rean, Stereo, Open Circuit
3 pole open 1/4" jack, 3 contacts, with washer and nut, panel thickness 3.5 mm, with 0.205" faston tabs
$1.40
P-ECB-24A Potentiometer - Dunlop Hot Potz, 470 kΩ
Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.
$23.50
P-H1590BB-GORVA-X Chassis Box - GØRVA Design, S90, Diecast, 4.61" x 3.54" x 1.38"
Colors Available:
The Gorva S90 is a high quality powder-coated take on the Hammond 1590BBM size enclosure with a focus on function and design. Features:
  • Beveled top and rounded corners for high quality look.
  • Tight fit and small gap between the enclosure and lid.
  • Undercut boss allows more internal room for more flexible layout.
  • Smooth, eggshell-like matte powder coating.
  • Add 0.16" to enclosure depth for lid.
$14.95
P-QTL074 Op-Amp - TL074, Quad, Low-Noise, JFET Input, 14-Pin DIP
Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:
  • Wide common-mode and differential voltage range
  • Low input bias and offset current
  • Low noise en = 15 nV/HZ
  • Output short-circuit protection
  • High input impedance JFET input stage
  • Low harmonic distortion: 0.01%
  • Internal frequency compensation
  • Latch up free operation
  • High slew rate: 16 V/us (typical)
$1.15
S-H901-PC-X ¼" Jack - Cliff, PC Mount, for Marshall, metal nut
PC terminals, switched. Metal ferrule, vintage style.
Starting at $2.30
Don't see what you're looking for? Send us your product suggestions!