Pedal Parts / DIY
Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Black/R allows the user to power over-sized effect units or units w/AC jacks in hard-to-reach places off of the Power-All Daisy Chain. The Cable-Black can be connected to any plug on any Power-All daisy chain, or directly to the ECO-Dapter® itself.
$3.25
Rubber feet with screws for Dunlop Crybaby Wah pedal. Package of four. Original Dunlop replacement part. Rubber foot diameter: 5/8" Rubber foot height: 5/16" Screw threading: #6-32 (screw extends 5/16" beyond the rubber surface)
$3.95
package of 4
High quality phenolic knob with a classic chicken head design. This knob has an infilled indicator line. Fits 0.25” (6.35mm) shafts with set screw and brass insert.
- Height: 0.485 in.
- Length: 1.25 in.
- Fits ¼" shaft with set screw
- Brass Insert
- High Quality Phenolic
$1.85
TL061 single op amp in an 8-pin DIP package. The JFET-input operational amplifiers of the TL06x series are designed as low-power versions of the TL08x series amplifiers. They feature high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents. The TL06x series features the same terminal assignments as the TL07x and TL08x series. Features
- Very Low Power Consumption
- Typical Supply Current: 200 µA (Per Amplifier)
- Wide Common-Mode and Differential Voltage Ranges
- Low Input Bias and Offset Currents
- Common-Mode Input Voltage Range Includes VCC+
- Output Short-Circuit Protection
- High Input Impedance: JFET-Input Stage
- Internal Frequency Compensation
- Latch-Up-Free Operation
- High Slew Rate: 3.5 V/µs Typical
$0.69
Linear taper, right angle, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.
The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.
$2.39
CD4024B is a 7-stage ripple-carry binary counter. All counter stages are master-slave flip-flops. The state of a counter advances one count on the negative transition of each input pulse; a high level on the RESET line resets the counter to its all zeros state. Schmitt trigger action on the input-pulse line permits unlimited rise and fall times.
$1.15
Prewired cup-shaped LED bezel with a red LED. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12V. Mounting nut and lock washer included.
$1.15
Colors Available:
Starting at $0.85
¼" female. Open circuit. Replacement for Fender®. Made in Taiwan.
$1.55
New old stock radial capacitors from Philips with 10mm lead spacing. The KT-347 series capacitors feature the same lacquer coating as the Mullard / Philips mustard caps found in classic Marshall amps and many vintage pedals. These NOS caps feature a low-inductive wound cell of metal foil and a polyethylene terephthalate film.
$2.25
High-quality USA made knobs from Davies Molding. The 1914 knob is the larger version of the classic 1900H found on countless synthesizers and pedals. This knob is made of solid phenolic and features an indicator line on the top. The knob pairs perfectly with the smaller diameter 1900 knobs such as the P-K801-BRASS-X as well as the skirted P-K234X knobs.
- Height: 0.50 in.
- Diameter: 0.75 in.
- Fits ¼" shaft with set screw
$3.55
Diagonal cutters with an attachment for catching cut leads. This set of cutting pliers is made from high quality carbon steel with a hardened finish. The catcher can also be removed for use with vacuum attachments.
$28.95
Colors Available:
Starting at $6.29
Atten TJ-228 soldering iron stand with adjustable mounting angle, sponge holder and solder spool stand. This stand is a great option for stand-alone soldering irons or as a replacement for a worn out stand.
$8.55
Small 42TM018 audio transformers with a 10KΩ:600Ω impedance. This transformer is a popular choice for pickup simulators in various effects such as fuzz pedals. The leads are soft metal wire and can be adjusted to fit a variety of applications. RoHS compliant. Rated for 200mW.
$5.55
Colors Available:
$7.50
3PDT latching footswitch with PC terminals. Blue with 9 terminals. Made in Taiwan.
$5.50
New old stock 2N404A PNP germanium transistors manufactured by Texas Instruments. These TI 2N404A feature gold plated leads. The 2N404A is used in many fuzz pedals along with other effects. The 2N404A is the same as the 2N404 but with a higher voltage rating. This transistor is in a TO-5 package with long leads commonly found on germanium transistors.
$12.00
Out of Stock
PCB for converting SMD QFN-32 packages to through hole DIP-32 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
$1.10
Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Note: As of 2023, Lumberg has updated the design of these jacks.
Note: As of 2023, Lumberg has updated the design of these jacks.
$1.55
Genuine Dunlop replacement housing screws for MXR/ Dunlop pedals. Replace lost screws and keep your battery access plate on tight. 6-32 thread, Phillips head.
$3.27
package of 4
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 3/8" centers.
$4.65
package of 5
Two rows of 6 U-style terminals (12 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick.
$1.95