Pedal Parts / DIY

Colors Available:
- Slightly beveled top and rounded corners for high quality look.
- Tight fit and small gap between the enclosure and lid.
- Undercut boss allows more internal room for more flexible layout.
- Smooth, eggshell-like matte powder coating.
- Recessed bottom lid
$14.95

Colors Available:
- Beveled top and rounded corners for high quality look.
- Tight fit and small gap between the enclosure and lid.
- Undercut boss allows more internal room for more flexible layout.
- Smooth, eggshell-like matte powder coating.
$14.95

Colors Available:
New!:
Starting at $5.95

Colors Available:
New!:
Measures 4.77" x 2.60" x 1.39".
Starting at $6.59

Colors Available:
New!:
Starting at $4.95

Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box.
$9.95

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$6.22

Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $7.07

Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $9.42

Colors Available:
Starting at $8.95

Same as Hammond P-H1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ ½" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.
$9.95

Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $11.32

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Six 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$19.34

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Six 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
$21.69

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Six 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
$27.31

Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $6.14

Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
$10.81

Special Order Item
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$23.15

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$14.34

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$13.02

Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$8.77

Box, Hammond, Unpainted Aluminum Enclosure, Octagon, 5.23" x 5.23" x 1.38"
$11.63

Colors Available:
$13.83

Hammond Mfg. Diecast Aluminum Chassis Box – 7.4” x 4.7” x 1.3”. Made in Taiwan. Key Features: • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure. • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. • Unpainted version is vibra finished for a smooth surface with no sharp edges. • Quantity six (6) 6-32 x 1/2” machine screws secure lid - into factory tapped holes.
$16.69