New Products

P-H549 Switch - Carling, Mini Toggle, SPDT, 3-Position, PC Pins
Carling mini-toggle switch, single pole/double throw, PC Pins. ¼" mounting hole diameter. 0.354" bushing length. 3-Position, On-Off-On.
$3.89
P-PC-3PDT-BOARD-X PCB - Daughterboard for Wiring 3PDT Footswitches
Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
Starting at $0.69
S-H9NT-R Nut - Cliff, Hex, Red, used on Loudspeaker Output Jacks
Red Cliff hex nut, often used on guitar amplifiers to identify loudspeaker outputs.
$0.59
On Backorder
S-HSO-M3-X Standoff - M3, Male-Female, Aluminum, 5.5mm Diameter
  • Finish/Plating: Clear Iridite
  • Material: Aluminum
  • OD: 5.5mm
  • Shape: Hex (Metric)
  • Style: M-F Standoff
  • Thread Depth(D): 8mm
  • Thread Length (TL): 8mm
  • Thread: M3
  • Type: Threaded Standoffs
Starting at $0.60
P-T-LEHLE-HZ-L Transformer - Lehle, Audio, Line Isolation, High Impedance
The Lehle Transformer HZ is the ideal component to avoid hum loops or to balance and unbalance signals without degrading the sound of high impedance signal sources.
$65.89
P-H-LEHLE-SW-X Relay Module - Lehle, Relay True Bypass Switching Unit
The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.
Starting at $21.89
P-T-LEHLE-MZ-L Transformer - Lehle, Audio, Line-Bridging, Unbalanced to Balanced
The LEHLE TRANSFORMER MZ is the ideal component to avoid hum loops without degrading the sound. It achieves this through galvanic isolation of low to mid impedance audio signal sources. It can be used as an input or output transformer, for balanced or unbalanced signals.
$43.89
P-H-LEHLE-BTN-X Footswitch - Lehle, SPST, Momentary, Soft Click, Long Life
The LEHLE SWITCH BTN is a momentary foot switch. It is housed in an M12 threaded enclosure made of stainless steel. Thanks to the gold plated contact material its life span is at least one million switching cycles electrically and mechanically. Hardware included.
Starting at $13.95
P-ST8-209MIP-EPC Socket - Belton, Micalex, 8-Pin Octal, MIP, Flanged Holes
Belton 8-pin Micalex tube socket commonly used for octal based power, preamp, and rectifier tubes. Applicable for use with all types of electronic equipment using vacuum tubes. This version has circular extruded holes.
$3.50
S-HS-M3-6-X Screw - M3, Painted, Combination Head, Binding, 6mm
Package of 5
Colors Available:
Combination Drive, Colored Head Binding Screws, 6mm, M3, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
$1.75
S-TST-SCREWDRIVER Soldering Iron Tip - Weller, solid core, screwdriver type, ST Series
Genuine Weller screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The screwdriver style is great for soldering through hole components and many other situations. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
Starting at $4.50
S-TET-SCREWDRIVER-L Soldering Iron Tip - Weller, hollow core, long screwdriver type, ET Series
Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.
Starting at $5.35
S-TET-SLOPED Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.45
P-H546 Switch - Carling, Mini Toggle, DPDT, 3-Position, PC Pins
Carling mini-toggle switch, double pole/double throw, PC Pins. ¼" mounting hole diameter. 0.354" bushing length. 3-Position, On-Off-On.
$3.89
S-TST8 Soldering Iron Tip - Weller, solid core, narrow screwdriver type, ST Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$5.15
S-TST5 Soldering Iron Tip - Weller, solid core, single flat / sloped type, ST Series
Genuine Weller single flat style tips for use with all ST Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$5.15
S-TET-SCREWDRIVER Soldering Iron Tip - Weller, hollow core, screwdriver type, ET Series
Genuine Weller screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The screwdriver style is great for soldering through hole components. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
Starting at $5.35
R-VADAPT-25 Potentiometer Adapter Sleeve - Converts 6mm or 18T shaft to ¼"
This brass adapter sleeve converts a 6mm shaft potentiometer or 18T knurled shaft potentiometer to 1/4" shaft (6.35mm), allowing for 1/4" knobs to be used on a wider range of potentiometers. 1/4" tall.
$0.53
P-H1590BBX Chassis Box - Hammond, Diecast Aluminum, 4.67" x 3.68" x 1.18"
Colors Available:
New!:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $9.42
S-H409X Wire Nut - 18-22AWG, 300V, Rated for 105°C
Package of 20
300V wire nuts for use with 18 gauge through 22 gauge wires. These wire nuts are great for use on appliances, televisions, stereos, antennas, or for any small wiring application. Rated for up to 105°C.
$1.40
R-G Resistors - ⅛ Watt, Metal Film
Package of 5
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. These 1/8W resistors have a very small body and are great for tight builds.
$0.75
R-N Resistors - ¼ Watt, Metal Film
Package of 5
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. Package of 5. These resistors are perfect for pedal builders! 1/4 watt.
$1.80
S-HS-SKT-X Screws - M3-0.5 Socket Head Cap, 8mm Length
Package of 5
Colors Available:
Ideal for precision assembly work with close tolerances and applications needing a well tooled appearance.
Starting at $0.75
S-HS-BTN-X Screws - M3-0.5 Button-Head Socket Cap, 8mm Long
Package of 5
Colors Available:
Button-Head Socket Cap Screws - Class 10.9, ISO 7380 Coarse Thread. Used when a wider bearing surface or smoother, more finished appearance is desired.
Starting at $0.75