New Products

W-AM-AC3MDZX XLR Jack - Amphenol, 3-Pole, Male, D Flange
Colors Available:
New!:
Amphenol AC "Z" series XLR metal chassis mount connector. 3 pole male, D Flange, Stamped contacts, Black Finish. The metal chassis mount "Z" series connectors are designed for the audio user where durability, reliability and strength across a wide range of applications are important. All AC products are manufactured to the highest quality standards and will withstand the harshest environments. Note: A ground tag is standard on all AC "Z" series connectors. Although the ground tag is intended for RFI shielding applications, Amphenol cannot guarantee its effectiveness in all cases.
Starting at $3.75
R-VTL5CX Optocoupler - Xvive, Vactrol, VTL5C Series
High quality vactrols from Xvive. The Xvive vactrols are clones of the original Excelitas / Perkins-Elmer vactrols used in man effects pedals, synthesizers, compressors and other equipment. These vactrols feature a thick epoxy sealed casing. The VTL5C3 and VTL5C3/2 both have a steep slope, good dynamic range, a very low temperature coefficient of resistance, and a small light history memory.
Starting at $5.50
P-G-TP-AX Tailpiece - Stop Bar, Vintage Spec, Aluminum, USA
Colors Available:
New!:
U.S. made and true to vintage 1950s specifications. This lightweight stop tailpiece is made of aluminum to match the original 1950s version. High quality plating is used on all options. Mounting studs sold separately. For a full set with all hardware included, please see P-GKLU-KLP1141X.
  • 3.22 in. (82mm) stud spacing
Starting at $21.95
P-G-BRG-A-N3 Bridge - ABR-1, Nonwired, Nylon Saddles, USA, nickel
Made in U.S. vintage spec ABR-1 bridge with no retaining wire and nylon saddles. Hardware sold separately. See P-GKLU-KLP1273N for a complete set. The bridge uses string tension along with the set screws to secure the nylon saddles onto the bridge.
  • Post spacing: 2.93 inches (74.5mm)
  • Radius: 12 inches (30.48cm)
  • String Spacing: 10.4 mm
$22.50
P-H501-L-X Footswitch - 3PDT, black body, Solder Lugs, Soft Click
Colors Available:
Black bodied 3PDT footswitches perfect for custom pedal builds. These footswitches feature a low actuation force for fast and responsive switching. Color options are available to dial in the look of your next build. Matching mounting hardware is included. Features
  • Latching Footswitch
  • 3PDT
  • Low Actuation Force
  • Solder Lugs
  • Matching Hardware Included
Starting at $2.45
P-H501-LP Footswitch - 3PDT, black body, Solder Lugs, Low Profile
Low profile switches with a smaller footprint than the standard 3PDT sizes. These footswitches are perfect for cramped layouts but are also great for general use. The small solder lugs are great for wiring by hand that also work well with PCB layouts. Mounting hardware included. Features
  • Latching Footswitch
  • 3PDT
  • Low Profile
  • Small Solder Lugs
  • Hardware Included
$3.35
P-K385X Knob - Pointer, Large, Knurled, vintage index line
Colors Available:
New!:
This vintage knob design has been used on numerous boutique pedals. These classy knurled pointer knobs are made from a solid mold, feature a slotted set screw, and fit ¼" solid shaft potentiometers. Davies 1470 clone.
Starting at $0.95
P-HBOARD-G10-X Turret Board - Blank, No Holes, Black G-10, 11-⅞" x 7-1/16”
Oversized blank G-10 epoxy boards perfect for custom turret or eyelet boards. The large size can be cut down to make multiple boards. With no predilled holes, builders can make clean custom layouts for their projects.
Starting at $8.95
P-Q-SSI2131 Integrated Circuit - SSI2131, VCO, Sound Semiconductor
The FatKeys™ SSI2131 Voltage Controlled Oscillator provides the core VCO function with buffered triangle, sawtooth, and variable-width pulse waveform outputs over a ten-octave range. The device offers unparalleled temperature stability, exponentiality, waveform integrity, and ease of use while requiring an absolute minimum of external components. The SSI2131 is a new-generation voltage controlled oscillator for high-performance electronic musical instruments and other systems requiring accurate audio-band waveform generation. The device offers unprecedented levels of temperature stability, exponentiality, waveform integrity, and ease of use.
$7.50
W-AM-AC3MAV2AUPRE XLR Jack - Amphenol, 3-Pole, Male, PC Mount
Plastic panel-mount male XLR jack from Amphenol with a vertical PCB mount. The AC series, A and B type XLR chassis receptacles have been designed and manufactured with the Original Equipment Manufacturers’ (OEM) needs in mind. The compact shell design allows a significant space saving over the traditional ‘D’ type shell. Gold plated contacts improve the performance, ensuring a reliable contact and the unique grounding link options offer flexibility in design. Features
  • Vertical PCB mount
  • Compatible with all other XLR brands
  • Gold Contacts
  • Precision Machined Pin contacts
$1.25
C-EC30X2-20-525 Capacitor - CE Mfg., 525V, 30/30/20 μF
CE Manufacturing USA Made Multi section Can Capacitor. Reproduced To Exact Mallory Specs Using Original Mallory Machinery.
  • 30/30/20uF 525VDC Electrolytic.
  • FP / Twist Lock Style. Solder Tabs.
  • -10%, +50% Tolerance, 55°C Temperature Rating.
  • 1 ⅜"D X 3"H.
$39.95
P-GGT-119-C Bridge - Gotoh, 510TS-FE1, Tremolo, Chrome
The Gotoh 510TS-FE1 tremolos are designed to withstand years of abuse and remain trouble free. This tremolo is precision machined and paired with steel saddles meant to last a lifetime. The patented FST tremolo block is designed to allow the strings to contact the saddle without touching the block as it passes through which increases sustain and tuning stability. The 510TS-FE1 also uses Gotoh’s patented Stud Lock system for increased mounting stability. Hardware included.
$108.95
On Backorder
P-H708 Control Plate - Jaguar Style, Selector Switch, Chrome
Jaguar style selector switch plate in chrome. Perfect replacement for most Jaguar style guitars. This version features the stock three switch configuration originally used for selecting pickups and engaging the mid-tone cut.
$5.95
R-V-COVER-X Dust Cover - Rubber covering for Potentiometers, black
Black dust cover for use with 16mm or 24mm potentiometers. These covers slide over the back of the pot covering the holes and gaps to help prevent dust from accumulating inside avoiding potential repairs and replacing down the road. The dust cover is made of a soft rubbery material and is easy to install on standard 24mm and 16mm pots.
Starting at $0.85
P-Q-SSIDAB2130 Integrated Circuit - DAB2130, VCO, Sound Semiconductor
The Sound Semiconductor DAB2130 is a pre-soldered DIP converter for the SSI2130. This board features the SSI2130 and two decoupling caps for the V+ and V- inputs. The pinout is labelled on the board and matches the QFN pinout. This adapter features a 32 pin DIP base with a .600 in. width. The pins are standard male headers so 2.54mm female headers are recommended for socketing the board. For the standard QFN version, please see P-Q-SSI2130. The first new VCO IC in decades, and worth the wait! The FatKeys™ SSI2130 Voltage Controlled Oscillator provides beautiful triangle, sawtooth, pulse, and square waveforms with unprecedented temperature stability; and adds an on-chip mixer, low distortion sine wave generator, through-zero FM/PM capability and more in an ultra-compact PCB footprint. The SSI2130 is a new-generation voltage controlled oscillator subsystem for high-performance electronic musical instruments.
$19.95
S-W902X Wire - Gavitt, Cloth, 22AWG Stranded, Top Coat Pre-Tinned
Sold by the foot
Colors Available:
New!:
High quality USA made Gavitt. This wire features an outer waxed cotton braid over a celanese braid. The wire is stranded 22AWG with a tinned overcoat (topcoat) so no additional tinning with a soldering iron is required for use. Sold by the foot.
$0.75
P-PC-SB400 Breadboard - Solderable PCB, 3.00” x 1.90”
The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.
$4.95
P-PC-PAD3U PadBoard - Double Sided, Plated Holes, 6.30” x 3.94”, Mounting Holes
The PadBoard-3U prototyping circuit board has a general purpose pad-per-hole pattern which is good for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. The PCB accepts a 96 pin DIN-41612 VME connector for backplane or board-to-board applications. Holes for ejector latches are provided. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$12.95
P-PC-ST3U StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$9.95
P-PC-ST2 StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$5.50
P-PC-PAD2 PadBoard - Double Sided, Plated Holes, 3.94” x 3.15”, Mounting Holes
The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)
$6.85
W-AM-AC3FDZX XLR Jack - Amphenol, 3-Pole, Female, D Flange
Colors Available:
New!:
Amphenol AC "Z" series XLR metal chassis mount connector. 3 pole female, D Flange, machined, black finish. The metal chassis mount "Z" series connectors are designed for the audio user where durability, reliability and strength across a wide range of applications are important. All AC products are manufactured to the highest quality standards and will withstand the harshest environments. Features
  • The “D” size housing can be either front or rear mounted using the same panel cutout
  • A leading first mate last break socket contact is standard on all female connectors (Pin 1)
  • Solder cup
  • Connectors are fitted with a grounding system for RFI shielding applications
  • Compatible with all other XLR brands

Note: A ground tag is standard on all AC "Z" series connectors.
Starting at $3.75
P-RP-TQ2-5V Relay - Panasonic, DPDT, 5V, Single Coil, Non-Latching
High quality non-latching relays from the Panasonic TQ series. These 5 volt relays are commonly used in pedals for true bypass switching. Relay switching can allow for a variety of options on pedal builds. Different footswitch modes can be obtained using the same momentary footswitch. Stereo switching using a standard footswitch is another possible option. Features:
  • Compact low profile size
  • Standard DIL spacing for easy PCB use and breadboard compatibility
  • Non-Latching
  • Single Coil
  • 5V Coil Voltage

For a latching version, please see P-RP-TQ2-L-5V.
$3.25
P-K850X Knob - Plastic, Set Screw, Fluted w/ Line, 0.745" Diameter
Colors Available:
Plastic control knob with set screw and brass insert. This knob features a distinctive fluting similar to the popular Philmore 3010 knob. This style is also similar to the small skirted MXR knobs. Fits ¼” (6.35mm) pot shafts.
$0.85