Maintenance Products

S-C10-302 Cement - GC Electronics, Service Cement
A quick-drying, waterproof clear adhesive which forms a strong, hard, water and vibration-resistant bond with minimal shrinkage. Ideal for speaker repairs and bonding semi-porus materials to each other or to metals, plastics, etc. 2 oz. bottle. Can be used as a glue for small speaker cone repairs.
$8.95
S-C10-8109 Heat Sink Compound - silicone, Type Z9, 1 oz
Type Z9, 1 fluid ounce. Silicone base, extra high-efficiency heat transfer. Made in USA. For mounting transistors, diodes, rectifiers, and resistors. Thermal joint compound for any device where efficient cooling is desired.
  • For effective transfer of heat between components & heat sinks
  • Will not dry or harden
  • White paste

Grease-like consistency; opaque white in color; zero bleed; very stable at elevated temperatures; excellent thermal resistance and high thermal conductivity; efficient thermal coupler; effective and positive heat sink sealers and heat transfer agent. The product offers high thermal conductivity, virtually no bleed or evaporation over a wide operating temperature range. It will not harden, dry out or melt after 1,000 hours at 200°C. Meets Mil-C-47009 and Mil-C-47113.
$6.75
S-C10-4702 Corona Dope - GC Electronics, lacquer coating, 2 oz.
Corona Dope is useful for insulating components, circuits and assemblies. It has high dielectric strength and is especially useful where high voltages are involved. Also has excellent arc and corona resisting properties and protects surfaces against moisture. Cures in 20 minutes at room temperature.
  • Color: Black
  • Specific Gravity: 0.9
  • Dielectric Strength: 3800 V/Mil
  • Softening Point: 180°C to 190°C
  • Temperature Range: Up to 340°F
  • Viscosity @ 25°C: 220 cps
$9.98
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $5.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50
S-F506X Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Starting at $5.95
S-F504X Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Starting at $5.50
S-C10-8602 Belt and Drive Non-Slip - GC Electronics
Prevents slippage in mechanical or electro-mechanical devices, which are driven with cords, belts, pulleys and drives. Restores proper functions on belts and drive pulleys in turntables, record changers and tape recorders, especially where the rubber parts have hardened and/or become slick and cause slippage.
  • Color: Clear to light brown
  • Specific Gravity: 0.91
  • Flash point: 54°F
  • Freezing Point: <90°C
  • Solubility in Water by wt.: 100% at 20°C
$7.95
S-F508X Adhesive - Bob Smith Industries, Extender Tip for Glue
Package of 6
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
  • Helps focus glue stream
  • Works with all three CA glue viscosities
  • Package of 6
Starting at $5.95
S-CIS-808 Solvent - Silicone Rubber Adhesive, IS-808, clear
Momentive clear IS808 adhesive sealant is compatible with rubber materials with a 24 hr cure time. Provides a 25 min fixture time. Delivers great performance with a shear strength of 150 psi, tensile strength of 300 psi and peel strength of 37 psi. Made in the USA.
$9.95
S-C10-1762 Liquid Tape - GC Electronics, Insulating Coating, 2 oz
Heavy black coating used as insulating tape in applications where tape cannot be used.
Insulating Coating is an air-dry, synthetic rubber coating that can be easily applied by spraying, brushing, or dipping. Insulating Coating resists moistures, acids, abrasion, weathering, electrical shock, skidding/slipping, and corrosion. Coats give a comfortable, controlled, color-coded grip to all types of tools, lawn and garden, mechanical, electrical, woodworking, masonry.
  • Covers 30 square feet per gallon at 15 mils
  • Cured temperature use range -30 to 200F
  • Tensile strength: 3,7540 psi
  • Dielectric Strength: 1,400 V/Mil
$10.45
S-CCW100P Pen - Caig, Circuit writer, for drawing traces
Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces(epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.
$23.95
S-CCOLORBOND-BLK Refinisher - Color Bond, Black, for Plastic, Leather, and Vinyl
ColorBond Leather, Vinyl & Hard Plastic Refinisher makes refinishing upholstery of all types easy and inexpensive. Created for painting leather, vinyl and plastic, ColorBond L, V & HP Refinisher quickly penetrates upholstery surfaces to create a molecular bond that seals in color. If you need a durable finish that won't flake, crack or peel, ColorBond L, V & HP Refinisher will deliver. Prepare upholstery for refinishing with S-CCOLORBOND-PREP.
$16.00
Don't see what you're looking for? Send us your product suggestions!