# Maintenance Products

Cement - GC Electronics, Service Cement
A quick-drying, waterproof clear adhesive which forms a strong, hard, water and vibration-resistant bond with minimal shrinkage. Ideal for speaker repairs and bonding semi-porus materials to each other or to metals, plastics, etc. 2 oz. bottle. Can be used as a glue for small speaker cone repairs.
$8.95 Adhesive - Bob Smith Industries, Insta-Cure Super Thin Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended. • Water-thin consistency • 1-3 second cure time • For tight fitting applications • Available in 1oz. and 2oz. sizes WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children! Starting at$5.50
Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50 Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506) Starting at$5.50
Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
• Convenient pump spray (2oz.
Starting at $5.95 Adhesive - Bob Smith Industries, Extender Tip for Glue Package of 6 Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application. • Helps focus glue stream • Works with all three CA glue viscosities • Package of 6 Starting at$5.95
Liquid Tape - GC Electronics, Insulating Coating, 2 oz
Heavy black coating used as insulating tape in applications where tape cannot be used.
Insulating Coating is an air-dry, synthetic rubber coating that can be easily applied by spraying, brushing, or dipping. Insulating Coating resists moistures, acids, abrasion, weathering, electrical shock, skidding/slipping, and corrosion. Coats give a comfortable, controlled, color-coded grip to all types of tools, lawn and garden, mechanical, electrical, woodworking, masonry.
• Covers 30 square feet per gallon at 15 mils
• Cured temperature use range -30 to 200F
• Tensile strength: 3,7540 psi
• Dielectric Strength: 1,400 V/Mil
\$10.45
Don't see what you're looking for? Send us your product suggestions!