Luthier Parts & Tools

W-SC-6J1233 ¼" Jack - Switchcraft, Acoustic End Pin, Mono / Stereo, Nickel
High quality acoustic end pin style jacks from Switchcraft. These nickel plated jacks have three conductors, a strain relief clamp, and a threaded shroud for a professional looking wiring job. The special strap nut can be removed to reveal a hex nut that can be used for external tightening of the jack.
$11.95
S-M401X Wire Sleeving - Spaghetti, Old-Style, 11 AWG
Sold by the foot
Colors Available:
New!:
11 AWG White fiberglass sleeving is varnished and closely resembles early style spaghetti. 20 AWG available with part number S-M436W. This is a coated fiberglass sleeving made by applying a proprietary blend of acrylic polymers to a closely woven electrical grade fiberglass substrate. This sleeving has excellent electrical, chemical and oil resistance properties, excellent heat stability and flexibility for ease of push-up and recovery. It exhibits excellent resistance to oils, acids and alkalis and solvents.
$0.75
C-G-100 Capacitor - Orange Drop, 100V, Polyester
Orange Drop 225P series Polyester film/foil capacitors, 100v, 10% tolerance. The 225P series capacitors in 100v rating are ideal for work in guitar wiring where a smaller footprint is needed to fit in the tight spaces often found in instrument control cavities. With over 35 years of proven dependability in the guitar and amp world you can count on Orange Drop caps to get you the tone you’re looking for. Features:
  • Non- inductively wound polyester film/foil construction
  • Radial lead
  • 10% tolerance
  • 100v voltage rating
  • Rated for 85°C operation
  • Tinned copper-clad steel leads
Starting at $1.95
R-VCXA-SP14 Potentiometer - CTS, Audio, Knurled Shaft, ¼" Bushing
CTS pots with a shorter ¼” bushing length that is perfect for pickguard mounted pots. These pots reduce the gap between the pickguard and bottom of the knob for a clean, near flush look. The shaft is a fine (24 tooth) knurl. Nut and lock washer are included.
The Series 450G Guitar Potentiometer is the same robust high-quality guitar potentiometer that has become the industry standard for top guitar manufacturers. Featuring reduced shaft wobble, low noise output, and smooth rotational feel, the Series 450G is supplied with standard tin-plated rear cover and solder lug terminals.
$4.50
P-H5419 Switch - Carling, Mini Toggle, DPDT, 2 Position, Solder Lugs, Flatted
Carling mini-toggle switch, DPDT, ideal for phase switching, coil-tapping, series/parallel pickup switching in guitars. This switch features a flattened actuator.
  • 0.354" bushing length
  • ¼" mounting hole diameter
  • Double pole/Double throw (DPDT)
$4.95
P-H5413 Switch - Carling, Mini Toggle, SPDT, 3 Position, Solder Lugs, Short Bat
Carling, SPDT mini toggle with short actuator, 3 positions, ¼" mounting hole diameter, 0.354" bushing length.
  • 0.354" bushing length
  • 3-Position On/Off/On
  • ¼" mounting hole diameter
  • Single pole/Double throw (SPDT)
  • Solder lugs
$3.49
P-H5418 Switch - Carling, Mini Toggle, SPDT, 2 Position, Solder Lugs, Flattened
Carling mini-toggle switch, SPDT. This switch features a flattened actuator.
  • 0.354" bushing length
  • 2-Position On/On
  • ¼" mounting hole diameter
  • Single pole/Double throw (SPDT)
  • Solder Lugs
$3.75
R-VC-KA-SP Potentiometer - CTS, Audio, Knurled Shaft, ⅜" Bushing
The 24mm body knurled shaft potentiometer features a 1/3 watt rating and a 3/8" bushing. 24 teeth slot and knurled shaft.
Includes:
  • 1 nut
  • 1 lock washer
$4.50
W-SC-152B ¼" Jack - Switchcraft, Stereo, double open circuit, deep panel
Type 152B. ¼" Female Stereo Input Jack 3-conductor. Thick panel-mount jack with cable clamp. Brass finish.
$7.95
P-H542X Switch - Carling, Mini Toggle, DPDT, 3 Position
Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs
  • DPDT ( Double Pole/ Double Throw) switch
  • 0.354" bushing length
  • 0.409” bat length
  • ¼" chassis hole diameter
  • Solder terminals
Starting at $3.10
P-H54-NUT-DRESS Nut - Dress Nut, For Mini Toggle Switches
Genuine Carling Technologies dress nuts for use with Carling mini toggle switches. These plated dress nuts feature a chamfered edge for a professional look and work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.
$0.49
R-VXK-SP Potentiometer - Fender®, 250kΩ, Audio, Knurled Shaft
250K ohm, audio taper. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging.
$6.95
R-VBM-XL Potentiometer - Bourns, Linear, Knurled Shaft, Mini
Bourns Mini Linear Taper Guitar pots. Mini Carbon Element, Split Shaft, Solder Lugs.
  • 17mm Body Diameter
  • ¼ watt
  • 300° rotation
  • ¼" Knurled 18-Spline Split Shaft
  • ⅜" Bushing Length
  • Tolerance: ±20 %
  • Maximum Operating Voltage: 200V
Starting at $2.80
P-COV-HNH-U-X Cover - Humbucker, No Holes, Nickel Silver, USA
Colors Available:
Original, made in USA, covers for humbucker pickups. These premium humbucker covers are made of nickel silver and have no holes.
Starting at $7.95
P-PUGT-2XA-X Pickup - Gotoh, HB-Classic Alpha, Humbucker, Made In Japan
The HB-Classic α is a vintage-style humbucker pickup. This pickup uses a made in USA Alnico 2 bar magnet for a smooth vintage tone. This pickup is wax-potted for sonic stability and uses a shielded 4-conductor wire for various wiring options. The HB-Classicα humbucker comes in various open and covered options to match the look of any guitar. Mounting screws and springs are included. Made in Japan.
Starting at $41.65
P-PUF53 Pickup - Fender®, Texas Telecaster Bridge / Neck
These overwound Tele pickups are constructed with AlNiCo 5 magnets and enamel coated magnet wire. The bridge pickup features height staggered magnets and a copper plated steel bottom plate for increased output, presence and midrange, while the nickel-silver cover on the neck pickup produces a clear warm tone that only a true Custom Shop Tele pickup can do. From Merle to Metal, the Texas Tele will demand their attention. Bridge:
  • DC Resistance: 10.5k
  • Inductance: 3.95H

Neck:
  • DC Resistance: 9.5k
  • Inductance: 3.3H

Fender part number: 099-2121-000
$155.95
P-PUK27 Pickup - Kent Armstrong, Icon 62 Neck, Strat (Alnico 3)
Slightly hotter even than the 57 models, these recreations of the 1962 Strat® single coil pickups deliver a true vintage tone that is a blast from the past. Middle position reverse wound/reverse polarity to achieve noise cancellation when utilizing a 5 way switch. 42 gauge Formvar wire and Alnico III magnets. White covers.
  • Magnet Type = Alnico 3 pole pieces
  • D.C. Resistance = 6.19k Ohms
  • Inductance (henrys) = 2.63
  • Wire Type = Formvar AWG 42
  • Lead Type = cloth insulated 2 conductor
  • Polarity = normal
$56.95
R-VX-S1 Potentiometer - Fender®, S-1, Knurled Shaft, 4PDT
The Fender® S-1™ switched pot is a stealthy way to mod a strat without drilling any extra holes. The switch can be configured for almost any configuration with its four double-throw poles. S-1™ pots use a 3/8” bushing.
$24.95
R-VBM Potentiometer - Bourns, Audio, Knurled Shaft, Mini
Bourns Mini Audio Taper Guitar pots. Mini Carbon Element, Split Shaft, Solder Lugs.
  • 17mm Body Diameter
  • ¼ watt
  • 300° rotation
  • ¼" Knurled 18-Spline Split Shaft
  • ⅜" Bushing Length
  • Tolerance: ±20 %
  • Maximum Operating Voltage: 150V
  • Series Number: PDB181-GTR
$2.80
P-HP-TUBE Pickup Tubing - Original Fender®, rubber
Package of 12
Genuine Fender®. Package of 12 pieces of rubber tubing for pickup mounting on most Fender instruments with pickguard-mount pickups.
$4.95
W-SC-W0213 Switch - Switchcraft, Pickup Selector, for Gibson® Straight
Colors Available:
Switchcraft Pickup Selector, Replacement for Gibson Straight-Type. As found on LP style solid body guitars.
Starting at $15.95
R-VCXJ-SS Potentiometer - CTS, J Taper, Solid Shaft, Panel Mount
CTS J Taper audio potentiometer.
  • Body Diameter: 24 mm
  • Power Rating ⅓ watt
  • Bushing Diameter: ⅜" (Threading: 3/8-32)
  • Bushing Length: 3/8"
  • Shaft Diameter: ¼"
  • Shaft Length: ⅜"
  • Shaft Material: Brass - Solid Shaft
$4.25
C-D-50V Capacitor - 50V, Ceramic Disc, ± 10%
50V ceramic capacitors with 5mm footprints for use in amplifiers, stomp boxes, and any other electronic project. These capacitors are small and should easily fit in any sized project. These also feature 1” lead lengths so they work great for point to point wiring.
$0.16
R-V250K-SS Potentiometer - Fender®, 250kΩ, Solid Shaft
250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender® packaging.
$6.95
Don't see what you're looking for? Send us your product suggestions!