Luthier Parts & Tools

P-K350 Knob - Fender®, Telecaster / P-Bass Barrel, Chrome
Package of 2
Fender Telecaster / P-Bass knurled flat-top barrel knobs in chrome.
$14.65
P-HP-TUBE Pickup Tubing - Original Fender®, rubber
Package of 12
Genuine Fender®. Package of 12 pieces of rubber tubing for pickup mounting on most Fender instruments with pickguard-mount pickups.
$4.95
P-G106-X Pickguard - for Standard Strat®, 11 Hole, 3-Ply
Colors Available:
Replacement pickguard for Fender® Standard Stratocaster models. These pickguards have eleven mounting holes and are cut for the classic strat configuration. Fits most American and Mexican Standard Stratocasters®. Features:
  • 3-ply / 2.5mm thickness
  • 11 mounting holes
  • Shielding over electronics cavity
  • Fits 3/8" bushing pots
  • Various colors available
Starting at $11.30
R-VBM2-500KM-SS Potentiometer - Bourns, Dual MN Taper, Solid Shaft, 500kΩ
Dual MN taper blend-balance with center detent. Solid shaft. 17 mm body diameter. ¼ watt, 300° rotation. 6mm shaft diameter. Solder lugs. 3/8" bushing.
$2.50
S-T261 Fret Press Inserts - for Pressing Frets, Multiple Radiuses
Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.
$6.99
P-MB-1-X Magnet - Bar, Alnico, Cast, 2.444", for pickups
Alnico cast bar magnets for use in humbucker and P-90 pickups. These are fully magnetized through the width and measure 2.444” x .5” x .125”.
$4.25
P-GTNN07 Nut - Bone, for Gibson, 43mm X 5.9mm X 8mm, Flat
Bone nut for Gibson®, 43mm x 5.9mm x 8mm at highest point with flat bottom.
$5.55
P-GGT-37-X Bridge - Gotoh, GE1996T, Floyd Rose® licensed
Colors Available:
The Gotoh GE1996T is a high end locking tremolo licensed by Floyd Rose. This version of the locking tremolo is a premium option that is great for new installs or upgrading original units. The hardened steel saddles and patented stud lock technology ensure a rock solid performance. Springs, spring claw, and all mounting hardware are included along with two hex wrenches for dialing in adjustments. 40mm block.
Starting at $104.60
R-V250K-SS Potentiometer - Fender®, 250kΩ, Solid Shaft
250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender® packaging.
$6.95
P-H705 Control Plate - Jaguar Style, Master, Chrome
Jaguar style master control plate in chrome. Perfect replacement for most Jaguar style guitars. 4.12” x 1.86” plate mounting center distance (0.14” diameter, recessed).
$9.95
R-V1M-SS Potentiometer - Fender®, 1M, Solid Shaft
1M ohm, Solid Shaft. Original Fender. Used for Volume and Tone control in many Fender guitars as well as amplifiers.
$5.85
P-GRV-102-18X Tuners - Grover, Rotomatic, 3 per side, 18:1 ratio
Package of 6
Colors Available:
The original Rotomatic® with an improved higher ratio gearing. The 18:1 ratio provides for finer tuning and greater stability. The finer gears provide smoother tuning and a higher degree of backlash elimination. This new version of the Rotomatic® uses the exact housing as the original. Only the gearing has changed. Includes washers, bushing and wood screws.
Starting at $52.25
P-GT-ARM-X Tremolo arm tip - Fender®, for capping tremolo arms
Package of 2
Colors Available:
Get better leverage and grip on your whammy bar by replacing the plastic tip, package of two. 10-32 thread size.
Starting at $3.55
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $6.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $6.50
S-T205 Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2
Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret
$4.30
P-GGT-24-X Tuners - Gotoh, 35G450, Lyra-style for Classical Guitar
Package of 6
Colors Available:
These parts are born from GOTOH's latest, state of the art manufacturing processes. In order to breathe life into these parts and build the finest machine heads in the world, they are exquisitely finished by skilled artisians, with absolutely no compromise. The work of craftsmen on each individual part has gained the classic machine heads of the 35G series, critical acclaim and trustworthiness in the eyes of musicians all over the world. These feature a 14:1 gear ratio for great tuning stability. Mounted 3-per-plate, 2 plates. Mounting hardware included.
Starting at $18.95
P-SW61 Switch - Pickup Selector, Strat, 5-Way, Black
5-way pickup selector switch for Stratocasters. Black switch tip.
$6.75
R-VB-CPSP Potentiometer - Bourns, Audio, Knurled Shaft, ⅜" Bushing
Bourns Audio Potentiometer, Vintage Premium, Conductive Polymer, Solder Lugs
  • 0.625" W x 0.377" L x 0.625" D
  • 300° rotation
  • Power Rating: ¼ watt
  • Tolerance: 10 %
  • ¼" Fine Knurled Split Shaft
  • ⅜" Bushing Length
  • J Hooks
  • Specifically designed for vintage guitars
  • Very Low Noise
Starting at $17.49
P-GGT-87-C Ferrules - Gotoh, TLB-1, for Guitar, Chrome
Package of 6
The Gotoh TLB-1 is a high quality set of guitar string ferrules. These press fit ferrules are a great choice for Telecaster® guitars or any guitar with a string through bridge. Includes six ferrules.
$4.25
P-GGT-17-X Tuners - Gotoh, GB707, Compact for Bass, 2 per side
Package of 4
Colors Available:
Precision 20:1 gear ratio enclosed Bass Guitar tuners. With a 7/16"-diameter string posts and threaded hex bushings. They require a 9/16"-diameter peghole for installation. Featuring sealed lubricated, cast housings and metal knobs. Mounting screws are included. Mounting hardware included.
Starting at $39.75
S-H119 Screws - Fender®, Saddle Height Screws
Package of 12
Set of hex set screws used for saddle-height adjustment on American Vintage series Stratocaster and Telecaster bridges.
  • Set of 12 hex set screws
  • For American Vintage Stratocaster and Telecaster guitars
  • Comes with four 4-40 x 3/8" hex screws and eight 4-40 x 5/16" hex screws.
$4.95
P-GT10X Bushings - Kluson, ¼" bushings, for retrofitting
Package of 6
Colors Available:
Adapter bushings to retrofit US 1/4 inch post Kluson tuners in a headstock drilled for modern die cast tuners. Nickel plating. Set of 6. These Kluson® steel replacement - adapter bushings are intended for use in converting a modern 10mm drilled headstock to accept a vintage Kluson stamped steel tuning machines with the original US 1/4 inch string post diameter. Many repair shops use these to convert a vintage instrument back to original peg head specs
Starting at $6.95
P-H546X Switch - Carling, Mini Toggle, DPDT, 3-Position, PC Pins
Carling mini-toggle switch, double pole/double throw, PC Pins. ¼" mounting hole diameter. 0.354" bushing length. 3-Position.
Starting at $3.50
Don't see what you're looking for? Send us your product suggestions!