Luthier Parts & Tools

Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs

• DPDT ( Double Pole/ Double Throw) switch
• 0.354" bushing length
• 0.409” bat length
• ¼" chassis hole diameter
• Solder terminals

Carling, SPDT mini toggle, 2 positions, ¼" mounting hole diameter, 0.354" bushing length.

Tokyo Cosmos aka TOCOS is known worldwide for their high quality potentiometers. The RV24 Series is a 24mm military-style carbon element potentiometer with a tolerance of 10%. The RV24 Series has been praised by both guitar and hifi amp builders for their performance and reliability. If you are looking for a top quality pot with a great feel, look no further than Tocos. Each linear taper potentiometer includes a nut, flush washer, and lock washer.

• 24mm diameter, single-turn potentiometers
• Carbon film element
• Metal shaft and bushing
• Panel mount
• Ear-lug solder terminals
• 6mm diameter slotted-end solid shaft
• 10mm bushing length
• 10mm shaft length (extended past bushing)
• Linear Taper

Brass tremolo stopper. Used as a floating bridge stop for Fender and Floyd Rose style tremolo systems. Prevents inadvertent vibrato effects produced by resting the picking hand over the bridge while playing. Allows for down-bends and prevents up-bends for a stabilized return of the whammy bar. Allen screw can be easily reversed to allow for a floating bridge setup again. Includes: (1) brass block (1.05" L x .39" W x .49" H) (1) allen key, 2 mm (1) allen screw (M4 x .70 thread, 20 mm length) (1) hex nut (M4 x .70 thread) (2) countersunk mounting screws (10 mm length)

CTS Audio, Long Shaft 3/4 in. bushing, split knurled shaft, 3/8 in. bushing diameter. Great in guitars that have a thicker carved top (ex. Les Paul) where added bushing length is required.

• Body Diameter: 24 mm
• Power Rating ¼” watt
• Bushing Diameter: ⅜" (Threading: 3/8-32)
• Bushing Length: 3/4"
• Shaft Diameter: ¼"
• Shaft Length: ⅜"
• Shaft Material: Brass – Knurled Shaft
• 24 teeth slot and knurled shaft
• Includes (1) Nut and (1) Lock Washer

Tokyo Cosmos aka TOCOS is known worldwide for their high quality potentiometers. The RV24 Series is a 24mm military-style carbon element potentiometer with a tolerance of 10%. The RV24 Series has been praised by both guitar and hifi amp builders for their performance and reliability. If you are looking for a top quality pot with a great feel, look no further than Tocos. Each audio taper potentiometer includes a nut, flush washer, and lock washer.

• 24mm diameter, single-turn potentiometers
• Carbon film element
• Metal shaft and bushing
• Panel mount
• Ear-lug solder terminals
• 6mm diameter slotted-end solid shaft
• 10mm bushing length
• 10mm shaft length (extended past bushing)
• Audio Taper

Solid shaft, linear. 24 mm body diameter. ¼" watt, 300° rotation. ¼" shaft diameter. Solder lugs. 3/8" bushing.

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 3 position switch with knob and mounting hardware.

Includes all parts but the magnet wire, all sets are ready for winding. Kits include Alnico 5 magnets, bobbins, poll screws, slug screws, baseplate, and coil lead wires.

Gibson style top hat knob. Fits fine knurled pot shafts.

The Switchcraft Type 112A enclosed ¼” jack is a high quality jack featuring a switched tip. This jack has three solder lugs. One for the tip, one for the sleeve, and one for the switch which connects to the tip when no plug is inserted. These jacks have been widely used across the industry and can also be found in many popular 5U synthesizers. Includes nut and washer

• Type 112AX
• 0.276" bushing length (standard)
• Mates with standard ¼" plugs and is available with 0.25" inside diameter bushing.
• Mono 2-Conductor
• Includes nut and washer
• Tip is shunt

A modern version of the Tune-o-matic style bridge for the solidbody guitar. Pre-notched saddles with an individual saddle intonation screw retained by mini hex nuts for each one. Threaded thumbwheel style studs and bushings and features hard zinc saddles. Hardware included.

Gibson style top hat knob. Fits fine knurled pot shafts.

Alnico cast bar magnets for use in humbucker and P-90 pickups. These are fully magnetized through the width and measure 2.444” x .5” x .125”.

Gibson style speed knob. For 24 teeth knurled shaft.

Pick guard screws, phillips, ovalhead. Great for mounting countersunk pickguards, control plates, etc.

• 7/16” threaded portion
• Available in Black, Gold, Nickel, and Chrome plating
• Package of 100

Replacement Butterbean (oval) press-on button for Kluson® tuning machines. Correct for vintage applications.

Fits .237" solid shaft pots. Set screw, .75" diameter, .73" height. Fits on Bourns miniature solid shaft pots.

Designed to polish all types of fret wire. Includes 24 × polish pads, 2 × fretboard guards, 1 × finishing cloth

A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without damaging the fretboard.

Ceramic disc capacitors rated for up to 2kV, ± 10% tolerance.

Switchcraft ¼" Mono 2-Conductor Input Jack, Isolated Make Circuit (Type 13). Includes nut and washer

Tele style control plate. 5.9” plate mounting center distance (0.123” diameter, recessed).

• Two potentiometer mounting holes for 3/8” bushing diameters
• One standard selector switch mounting slot (1.63” mounting center distance, 0.15” diameter, recessed)
• Made in Korea

Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.406” center-to-center mounting hole spacing
• #4-40 screws recommended for mounting
• Screws not included