Luthier Parts & Tools
Potentiometer - Fender®, S-1, Knurled Shaft, 4PDT
The Fender® S-1™ switched pot is a stealthy way to mod a strat without drilling any extra holes. The switch can be configured for almost any configuration with its four double-throw poles. S-1™ pots use a 3/8” bushing.
Potentiometer - PMT, Humbucker Control, Coil Filters
The HCP Humbucker Control Pot is a dual mode variable coil tap selector for electric guitars and basses that eliminates the additional switches associated with coil splitting a pair of humbuckers. In TAP mode, rotating the pot counterclockwise fades from humbuckers to outer coils (neck pickup South coil & bridge pickup North coil). Pulling the HCP control up and rotating it counterclockwise fades from humbuckers to inner coils (neck pickup North coil & bridge pickup South coil). Tonal control is expanded with the unique ability to coil tap both humbuckers in varying amounts. In COIL FILTER mode, turning the HCP control applies varying amounts of a specially tuned high frequency filter to only one coil of the selected coils of the humbuckers (either North or South coils can be filtered). This makes each pickup a single coil at high frequencies and a humbucker at lower frequencies which produces a sound similar to a pair of single coils but with a stronger, fuller tone and 50% less noise than coil tapping.
Potentiometer - Bourns, Linear, Knurled, Conductive Polymer
Linear, .75" bushing length. Conductive polymer, 0.625" W x 0.625" L x 0.5" D body. ¼" watt, 300° rotation. ¼" shaft diameter. Solder lugs. 3/8" bushing. Knurled split shaft.
Starting at $7.50
Potentiometer - Bourns, 500kΩ Audio, Knurled, Dual Mini
Bourns Mini Carbon Element, DPDT Push Pull Switch, Dual Audio, Split Shaft. ¼" watt, 300° rotation. Solder lugs.
- 17mm Body Diameter
- 300° rotation
- Power Rating: 0.1 watt
- ¼" Knurled 18-Spline Split Shaft
- DPDT Push-Pull Switch
- ⅜" Bushing Length
- Tolerance: ±20 %
- Maximum Operating Voltage: 150V
- Bourns Series Number PDB183-GTR21
Potentiometer - PMT, CTS, Audio, Variable Treble Bleed, ⅜"
The V-Treb Variable Treble Bleed Circuit for guitar and bass is available pre-installed on high quality volume pots from CTS and Bourns. The circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. The V-Treb circuit also also available separately for use on any other volume pot.
Potentiometer - Fender®, 250kΩ, Knurled Shaft, Push-Pull
250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.
Potentiometer - PMT, V-Treb, Audio Treble Bleed, ⅜" shaft
Precision Music Technologies V-Treb – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced.
Potentiometer - PMT, Audio, Variable Treble Bleed, ¾"
Precision Music Technologies V-Treb with 500KA CTS pot – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Pot: 24 mm body diameter, ¼” knurled split shaft. Bushing diameter = 3/8”, Bushing Length = 3/4”. PCB dimentions: 1.06” x 0.46” x 0.07”