Are you a DIY'er and enjoy building your own gear? Our kits range from beginner to advanced skills, so there is something for everyone!
KitsAre you a DIY'er and enjoy building your own gear? Our kits range from beginner to advanced skills, so there is something for everyone!
Effects Kit - MOD® Kits, The Wave, Spring Reverb
The Wave is a versatile stand-alone, tube driven analog spring reverb unit kit. It can be used in front of your guitar amp or as a line-level analog reverb effect for the recording studio. Two controls allow you to serve up a wide range of wetness from just a touch to over the top psychedelia. The "dwell" control adjusts the input signal level driving the tank and the "reverb" control adjusts the level of output reverberations from the tank. The Wave's all tube design utilizes four dual triode vacuum tubes - three 12AX7s and one 12AT7 - and comes with a MOD® three-spring reverb tank. MOD® reverb tanks are deemed the closest to the original reverb tanks from the '60s made today. The Wave's reverb function can be switched in and out pop-free via the front panel toggle or with a footswitch. Footswitch sold separately (see P-H470 for compatible footswitch).
Amp Kit - MOD® Kits, MOD102 guitar amplifier
The MOD 102 is a great place to start for those interested in building their own tube amp. It is based on a classic American tube-circuit design combined with a British style Class A output tube section. At low volume it produces a clean chimey tone that moves into smooth overdrive at higher volumes. All parts are included along with a pre-drilled steel chassis, wire and tubes (1 EL84 and 1 12AX7). Puts out at least 5 watts. The chassis layout is open for easy assembly using the clear, easy to follow instructions.
Amp Kit - MOD® Kits, MOD102+ guitar amp
The MOD102+ expands on the same all analog vacuum tube classic American circuit design combined with a British style Class A output section as the Original MOD102 with some much added special “+” features. These special features include a three position progressive toggle switch for off-standby-power and additional push-pull functionality for each control - pull out the bass control knob for “mid boost”, pull out the treble control knob for “bright”, pull out the volume control knob for “turbo”.
Snubber Kit - eliminate fuzz from amplifier
Snubber parts kit for circuits. Used to build a "snubber circuit" to remove unwanted high frequencies and high voltages resulting from output transformer ringing in a guitar amplifier, without the "brick wall" effect of using diodes.
Starting at $8.25
Amp Kit - MOD® Kits, MOD101 guitar amplifier
MOD 101 Guitar Amp Kit Features:
- All Tube Design (solid-state diodes used only for full-wave rectification)
- 60W output power into 4, 8, 16 and 20 Ω
- 1 channel with customizable: tone stack, power tubes, negative feedback, input miller capacitance volt divider/LP filter, and preamp cathode bypass cap (all parts included)
- Vintage channel controls: bass, treble and volume
- Vintage pilot lamp and screw-on jewel cover for power-on indication
- DPDT power switch circuit for instant high-voltage drain in power-off
- Standby Switch
Amp Mod Kit - MOD® Kits, Bass to Tremolo Conversion Kit
This kit adds tremolo to silverface Fender® Bassman amps such as the Bassman 70 or Bassman 100. Using the tube from the Bass Instrument channel, the circuit is modified into the classic tube tremolo circuit. The Volume and Treble knobs become the Speed and Intensity controls while the Bass knob is replaced with a jack for the footswitch. The Bright switch becomes an On/Off switch for the tremolo when not using a footswitch.
Amp Mod Kit - MOD® Kits, Tone Stack Mod
This kit converts the TMB tone stack of a blackface or silverface amp to a modern aggressive voiced tone stack. The modification is achieved by replacing capacitor and resistor values in the original tone stack. All parts required for the conversion are included in the kit along with detailed picture instructions.
Amp Mod Kit - MOD® Kits, Normal to Bass Conversion
This kit converts the Normal channel of a blackface or silverface amp into the classic Bass Instrument channel from Bassman amps. This modification is achieved by altering the tone stack and works for both TMB and TB tone stacks. All parts required for the conversion are included in the kit along with detailed picture instructions.
Amp Mod Kit - MOD® Kits, 6L6GC to EL34 Conversion
This kit converts a standard class A/B dual 6L6GC power amp to a dual EL34 power amp. Changing the screen grid resistors along with altering the bias circuit is required for this modification. All parts necessary to complete the conversion are included along with detailed picture instructions. A matched pair of EL34 tubes is included with the kit.
LiteIIB 18W Kit - Scratch Build Parts
Package of 22GuitarAmplifierPCBs.com 18 Watt LiteIIb "Baby Will" Parts List for Scratch Build The Baby Will is a PCB simplified version of the legendary Marshall 18 Watt 1974x circuit. The circuit we laid out on a circuit board is known as the LiteIIb. It's capable of tone from clean jazz, crunchy blues, to raunchy classic rock. Crank up the volume and you'll be in AC/DC Back In Black heaven. The magic of the LiteIIb is its simplicity.
LiteIIB 18W Kit - Valve Junior Conversion Parts
Package of 20Convert your Epiphone Valve Jr. into a Lite IIb 18 Watt amp using the "Baby Will" kit. The Baby Will is a PCB simplified version of the legendary Marshall 18 Watt 1974x circuit. The circuit laid out on a circuit board is known as the LiteIIb. It's capable of tone from clean jazz, crunchy blues, to raunchy classic rock. Crank up the volume and you'll be in AC/DC Back In Black heaven