Integrated Circuits

LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded

The AS3080ED is Alfa’s version of the CA3080 IC in an SOIC package. The AS3080ED is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080ED has differential input and a single-ended, push-pull, class A output. Amplifier bias input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080ED is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.

CD4016B Series types are quad bilateral switches intended for the transmission or multiplexing of analog or digital signals. Each of the four independent bilateral switches has a single control signal input which simultaneously biases both the p and n device in a given switch on or off. Features:

• 20-V digital or ± 10-V peak-to-peak switching
• 280- typical on-state resistance for 15-V operation
• Switch on-state resistance matched to within 10 typ. over 15-V signal-input range
• High on/off output-voltage ratio: 65 dB typ. @ fis = 10 kHz, RL = 10 k
• High degree of linearity: <0.5% distortion typ. @ fis = 1 kHz, Vis = 5 Vp-p, VDD–VSS
• Extremely low off-state switch leakage resulting in very low offset current and high effective off-state resistance: 100pA typ.

The CD4070B contains four independent Exclusive-OR gates. The CD4070B provides the system designer with a means for direct implementation of the Exclusive-OR functions, respectively. Features:

• High-Voltage Types (20V Rating)
• CD4070B - Quad Exclusive-OR Gate
• Medium Speed Operation
• tPHL, tPLH = 65ns (Typ) at VDD = 10V, CL = 50pF
• 100% Tested for Quiescent Current at 20V
• Standardized Symmetrical Output Characteristics
• 5V, 10V and 15V Parametric Ratings
• Maximum Input Current of 1µA at 18V Over Full Package Temperature Range
• 100nA at 18V and 25°C
• Noise Margin (Over Full Package Temperature Range)
• 1V at VDD = 5V, 2V at VDD = 10V, 2.5V at VDD = 15V
• Meets All Requirements of JEDEC Standard No.

This quad flip flop is a part used in our Relay True Bypass Switching Part 2: Momentary and Soft Touch Switches article. To read the full article and learn about a circuit for relay switching in stomp box effects, please see the following link. https://www.amplifiedparts.com/tech-articles/relay-true-bypass-switching-2 These monolithic, positive-edge-triggered flip-flops utilize TTL circuitry to implement D-type flip-flop logic. All have a direct clear input, and the '175, 'LS175, and 'S175 feature complementary outputs from each flip-flop. Information at the D inputs meeting the setup time requirements is transferred to the Q outputs on the positive-going edge of the clock pulse. Clock triggering occurs at a particular voltage level and is not directly related to the transition time of the positive-going pulse.

PCB for converting SMD SSOP-20 packages to through hole DIP-20 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

LM311 single comparator IC in an 8-pin DIP package. The LM311 device is a single high-speed voltage comparator. These devices are designed to operate from a wide range of power supply voltages, including ±15-V supplies for operational amplifiers and 5-V supplies for logic systems. The output levels are compatible with most TTL and MOS circuits. These comparators are capable of driving lamps or relays and switching voltages up to 50 V at 50 mA. All inputs and outputs can be isolated from system ground. The outputs can drive loads referenced to ground, VCC+ or VCC−. Offset balancing and strobe capabilities are available, and the outputs can be wire-OR connected.

PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.

NE5532 dual op amp in an 8-pin DIP package. The NE5532 device is a high-performance operational amplifier combining excellent DC and AC characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage. Features

• Equivalent Input Noise Voltage: 5 nV/√Hz Typ at 1 kHz
• Unity-Gain Bandwidth: 10 MHz Typ
• Common-Mode Rejection Ratio: 100 dB Typ
• High DC Voltage Gain: 100 V/mV Typ
• Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
• High Slew Rate: 9 V/μs Typ

The AS3310 is Alfa’s version of the CEM3310 IC. The AS3310 is a self-contained, precision ADSR type of envelope generator intended for electronic music and other sound generation applications. Attack, decay and release times are exponentially voltage controllable over a wide range, and the sustain level is linearly voltage controllable from 0 to 100% of the peak voltage Vp. All four control Inputs are Isolated from the rest of the circuitry so that the control pins of tracking units may be simply tied together.
On the negative power output, there is an internal Zener diode at 7.4 volts ± 10%, which allows the chip to supply a maximum voltage of ± 15 volts with a current-limiting resistor REE, and a minimum positive supply voltage of + 11 volts and a minimum negative supply voltage of -5 volts.. A series current limiting resistor must be added between pin 6 and the supply.

CD4021B series types are 8-stage parallel- or serial-input/serial output registers having common CLOCK and PARALLEL/SERIAL CONTROL inputs, a single SERIAL data input, and individual parallel "JAM" inputs to each register stage. Each register stage is D-type, master-slave flip-flop. In addition to an output from stage 8, "Q" outputs are also available from stages 6 and 7. In the CD4021B serial entry is synchronous with the clock by parallel entry is asynchronous. Entry is controlled by the PARALLEL/SERIAL CONTROL input. When the PARALLEL/SERIAL CONTROL input is low, data is serially shifted into the 8-stage register synchronously with the positive transition of the clock line. When the PARALLEL/SERIAL CONTROL input is high, data is jammed into the 8-stage register via the parallel input lines and synchronous with the positive transition of the clock line.

LM358 dual op amp in an 8-pin DIP package. These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems.

The CD4077B contains four independent Exclusive-NOR gates. The CD4077B provides the system designer with a means for direct implementation of the Exclusive-NOR functions, respectively. Features:

• High-Voltage Types (20V Rating)
• CD4077B - Quad Exclusive-NOR Gate
• Medium Speed Operation
• tPHL, tPLH = 65ns (Typ) at VDD = 10V, CL = 50pF
• 100% Tested for Quiescent Current at 20V
• Standardized Symmetrical Output Characteristics
• 5V, 10V and 15V Parametric Ratings
• Maximum Input Current of 1µA at 18V Over Full Package Temperature Range
• 100nA at 18V and 25°C
• Noise Margin (Over Full Package Temperature Range)
• 1V at VDD = 5V, 2V at VDD = 10V, 2.5V at VDD = 15V
• Meets All Requirements of JEDEC Standard No.

The FatKeys™ SSI2131 Voltage Controlled Oscillator provides the core VCO function with buffered triangle, sawtooth, and variable-width pulse waveform outputs over a ten-octave range. The device offers unparalleled temperature stability, exponentiality, waveform integrity, and ease of use while requiring an absolute minimum of external components. The SSI2131 is a new-generation voltage controlled oscillator for high-performance electronic musical instruments and other systems requiring accurate audio-band waveform generation. The device offers unprecedented levels of temperature stability, exponentiality, waveform integrity, and ease of use.

PCB for converting SMD QFN-32 packages to through hole DIP-32 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.

The SSI2130 offers unprecedented performance and features, but its ultra-compact QFN package can present prototyping challenges. The EVB2130 eases evaluation by providing a PCB that allows comprehensive exploration of capabilities. The EVB2130-P is fully populated and ready for the bench. With the exception of the SSI2130, all components are through-hole for easy construction and experimentation. A on-board +5V regulator and 2.5V reference simplify external power connections, and pots are provided for mixer control, PWM, and VCO setup. Switches ease selection of saw ramp direction plus Through-Zero and Pulse Modulation. Features

• PCB size: 108 x 82mm
• External Power: ±12V
• Inputs: Expo Freq 1V/Oct PWM In Aux 1 and 2 In FM In PM In Hard Sync Soft Sync
• Outputs: Sine Saw Triangle Pulse Square Mix Out

The AS3340A is Alfa’s version of the CEM3340 IC. The AS3340A is a completely self-contained, precision voltage controlled oscillator, featuring both exponential and linear control scales and up to four buffered output waveforms: triangle, sawtooth, square, and pulse with voltage controllable pulse width. Full temperature compensation makes these VCOs extremely stable, and eliminates the need for a temperature compensation resistor. The highly accurate exponential and linear control inputs are virtual ground summing nodes, allowing multiple control voltages to be mixed within the device itself.
Also included is provision for hard and soft synchronization of the frequency, and an output for easy adjustment of high frequency tracking. Special care in the design ensures oscillation start-up under any power-on sequence and supply conditions.
An on-chip 7.4 volt Zener diode allows the device to operate off ±15 volt supplies, as well as +12, -5 volt supplies.

CD4027B is a single monolithic chip integrated circuit containing two identical complementary-symmetry J-K flip flops. Each flip-flop has provisions for individual J, K, Set, Reset, and Clock input signals. Buffered Q and Q signals are provided as outputs. This input-output arrangement provides for compatible operation with the CD4013B dual D-type flip-flop. The CD4027B is useful in performing control, register, and toggle functions. Logic levels present at the J and K inputs along with internal self-steering control the state of each flip-flop; changes in the flip-flop state are synchronous with the positive-going transition of the clock pulse.

LM380 power amp in a 14-pin DIP package. The LM380 is a power audio amplifier for consumer applications. In order to hold system cost to a minimum, gain is internally fixed at 34 dB. A unique input stage allows ground referenced input signals. The output automatically self-centers to one-half the supply voltage. The output is short circuit proof with internal thermal limiting. The package outline is standard dual-in-line. The LM380N uses a copper lead frame. The center three pins on either side comprise a heat sink.

CD4093B consists of four Schmitt-trigger circuits. Each circuit functions as a two-input NAND gate with Schmitt-trigger action on both inputs. The gate switches at different points for positive- and negative-going signals. The difference between the positive voltage (VP) and the negative voltage (VN) is defined as hysteresis voltage (VH). Features:

• Schmitt-trigger action on each input with no external components
• Hysteresis voltage typically 0.9 V at VDD = 5 V and 2.3 V at VDD = 10 V
• Noise immunity greater than 50%
• No limit on input rise and fall times
• Standardized, symmetrical output characteristics
• 100% tested for quiescent current at 20 V
• Maximum input current of 1 µA at 18 V over full package-temperature range, 100 nA at 18 V and 25°C
• 5-V, 10-V, and 15-V parametric ratings
• Meets all requirements of JEDEC Tentative Standard No.

The Sound Semiconductor DAB2140 is a pre-soldered DIP converter for the SSI2140. This board features the SSI2140 and two decoupling caps for the V+ and V- inputs. The pinout is labelled on the board and matches the SSOP pinout. This adapter features a 20 pin DIP base with a .600 in. width. The pins are standard male headers so 2.54mm female headers are recommended for socketing the board. For the SSOP version, please see P-Q-SSI2140. A refresh of a classic design, the FatKeys™ SSI2140 preserves mojo of the beloved SSM2040 and adds temperature compensation of gm cells and the exponential control port. A "Q VCA" is provided to allow easy resonance control as well as various options for Q compensation.

TC1044 charge pump voltage converter in an 8 pin DIP package. The TC1044S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding –1.5V to –12V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+.

Quad low-power opamps in an 14-pin DIP package. The LM324 offers a 1MHz bandwidth and can be powered from a single supply.