Integrated Circuits

P-QTL072 Op-Amp - TL072, Dual, Low-Noise, JFET Input, 8-Pin DIP
The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
P-Q4558 Op-Amp - NJM4558, Dual high-gain, 8-Pin DIP
Dual Operational Amplifier. The NJM4558 (JRC4558) integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip using an advanced epitaxial process. Combining the features of the NJM741 with the close parameter matching and tracking of a dual device on a monolithic chip results in unique performance characteristics. Excellent channel separation allows the use of the dual device in single NJM741 operational amplifier applications providing density. It is especially well suited for applications in differential-in, differential-out as well as in potentiometric amplifiers and where gain and phase matched channels are mandatory. Features:
  • Operating Voltage (±4V~±18V)
  • High Voltage Gain (100dB typ.)
  • High Input Resistance (5MΩ typ.)
  • Bipolar Technology
P-QRC4558 Op-Amp - RC4558, Dual, Low Noise, 8-Pin DIP
RC4558 dual op amp in an 8-pin DIP package. The RC4558 device is a dual general-purpose operational amplifier, with each half electrically similar to the µA741, except that offset null capability is not provided. The high common-mode input voltage range and the absence of latch-up make this amplifier ideal for voltage-follower applications. The device is short-circuit protected, and the internal frequency compensation ensures stability without external components. Features
  • Continuous Short-Circuit Protection
  • Wide Common-Mode and Differential Voltage Ranges
  • No Frequency Compensation Required
  • Low Power Consumption
  • No Latch-Up
  • Unity-Gain Bandwidth: 3 MHz Typ
  • Gain and Phase Match Between Amplifiers
  • Low Noise: 8 nV/√Hz Typ at 1 kHz

  • DVD Recorders and Players
  • Pro Audio Mixers
P-QNE5532P Op-Amp - NE5532, Dual, Low Noise, Audio, 8-Pin DIP
NE5532 dual op amp in an 8-pin DIP package. The NE5532 device is a high-performance operational amplifier combining excellent DC and AC characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage. Features
  • Equivalent Input Noise Voltage: 5 nV/√Hz Typ at 1 kHz
  • Unity-Gain Bandwidth: 10 MHz Typ
  • Common-Mode Rejection Ratio: 100 dB Typ
  • High DC Voltage Gain: 100 V/mV Typ
  • Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
  • High Slew Rate: 9 V/μs Typ
P-QOPA2134 Op-Amp - OPA2134, Dual, High Performance Audio, 8-Pin DIP
OPA2134 SoundPlus™ Audio dual op-amp with low distortion, low noise and precision. The OPA2134 are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA2134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA2134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.
P-Q4580D Op-Amp - NJM4580D, Dual, Audio, DIP 8
The NJM4580D (JRC4580) is a dual opamp popularly used in many distortion pedals. This chip is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools. It is also suitable for the headphone amp at higher output current, and furthermore, it can be applied for the handy type set operational amplifier of general purpose in application of low voltage single supply type which is properly biased of the low voltage source. Features:
  • Operating Voltage ±2V~±18V
  • Low Input Noise Voltage 0.8µVrms typ.
P-QTL082 Op-Amp - TL082, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.
P-QTL022 Op-Amp - TL022, Dual, Low Power, 8-Pin DIP
TL022 dual op amp in an 8-pin DIP package. The TL022 is a dual low-power operational amplifier designed to replace higher power devices in many applications without sacrificing system performance. High input impedance, low supply currents, and low equivalent input noise voltage over a wide range of operating supply voltages result in an extremely versatile operational amplifier for use in a variety of analog applications including battery-operated circuits.
P-QLM13700 OTA - LM13700, Dual, Linearizing Diodes and Buffers, 16-Pin DIP
The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.
P-QBA4560 Op-Amp - BA4560, Dual, General Purpose, 8-Pin DIP
The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.
On Backorder
P-QLM833 Op-Amp - LM833, Dual, Low Distortion, Audio, 8-Pin DIP
LM833 dual op amp in an 8-pin dip package. The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier IC utilizes new circuit and processing techniques to deliver low noise, high speed and wide bandwidth without increasing external components or decreasing stability. The LM833 is internally compensated for all closed loop gains and is therefore optimized for all preamp and high level stages in PCM and HiFi systems. The LM833 is pin-for-pin compatible with industry standard dual operational amplifiers. Features
  • Wide dynamic range: >140dB
  • Low input noise voltage: 4.5nV/ √ ^Hz
  • High slew rate: 7 V/μs (typ); 5V/μs (min)
  • High gain bandwidth: 15MHz (typ); 10MHz (min)
  • Wide power bandwidth: 120KHz
  • Low distortion: 0.002%
  • Low offset voltage: 0.3mV
  • Large phase margin: 60°
P-QLM1458 Op-Amp - LM1458, Dual, 8-Pin DIP package
LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features
  • No Frequency Compensation Required
  • Short-Circuit Protection
  • Wide Common-Mode and Differential Voltage Ranges
  • Low-Power Consumption
  • 8-Lead TO-99 and 8-Lead PDIP
  • No Latch Up When Input Common Mode Range is Exceeded
P-QLM358 Op-Amp - LM358, Dual, 8-Pin DIP package
LM358 dual op amp in an 8-pin DIP package. These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems.
P-QNJM4580L Op-Amp - NJM4580L, Dual, Audio, 8-Pin SIP
NJM4580L dual op amp from JRC in a SIP8 package. The NJM4580L is the same as the DIP NJM4580 (JRC4580) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4580 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools.
P-QTL062 Op-Amp - TL062, Dual, Low-Power, JFET Input, 8-Pin DIP
Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.
P-QLF353 Op-Amp - LF353, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.
P-QNJM4558L Op-Amp - NJM4558L, Dual high-gain, 8-Pin SIP
NJM4558L dual op amp from JRC in a SIP8 package. The NJM4558L is the same as the DIP NJM4558 (JRC4558) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4558L is a dual high-gain operational amplifier with internal compensation circuit and constructed on a single silicon chip. It offers excellent characteristics by combining the parameters adjusted for a monolithic chip. The channel separation characteristic is suitable for measuring instruments. Features:
  • Operating Voltage ( ±4V~±18V )
  • High Voltage Gain ( 100dB typ. )
  • High Input Resistance ( 5MΩ typ. )
  • Bipolar Technology

See P-Q4558 for the DIP version of this chip
P-QNE5532 Op-Amp - NJM5532, Dual, Low-Noise, 8-Pin DIP
The NJM5532 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:
  • Operating Voltage = ±3V~±22V
  • Small Signal Bandwidth = 10MHz typ.
  • Output Drive Capability = 600Ω,10Vrms typ.
  • Input Noise Voltage = 5nV/√Hz typ.
  • Power Bandwidth = 140kHz typ.
  • Slew Rate = 8V/µs typ.
  • Bipolar Technology
P-Q-SSI2162 Integrated Circuit - SSI2162, Dual VCA, Sound Semiconductor
The FatKeys™ SSI2162 provides two independent VCA channels, and like its SSI2161 and SSI2164 siblings offers great flexibility in design of dynamics processors, automatic or remote level control, and voltage controlled filters. Highly compact 10-lead SSOP package. The SSI2162 is a versatile VCA building block for high-performance audio applications. Two independent channels provide voltage control of a current-mode input and output for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The device offers considerable flexibility for a wide range of design goals and applications. A unique mode control allows selection of Class A, Class AB, or in-between using a single resistor. In addition, improved current handling allows use of lower value input resistors for reduced output noise without loss of headroom. Both channels can be parallel-connected for further noise improvement.
P-QCD4013 CMOS - CD4013, Dual D-Type Flip-Flop, 14-Pin DIP
The CD4013B device consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q and Q outputs. These devices can be used for shift register applications, and, by connecting Q output to the data input, for counter and toggle applications. The logic level present at the D input is transferred to the Q output during the positive-going transition of the clock pulse.
P-QCD4052 CMOS - CD4052, 4:1, 2-Channel General-Purpose Multiplexer, 16-Pin DIP
The CD4052B analog multiplexers are digitally-controlled analog switches having low ON impedance and very low OFF leakage current.
P-Q-AS3360 Integrated Circuit - AS3360, Dual VCA, Alfa, 14-Pin Dip
The AS3360 is Alfa’s version of the CEM3360 IC. The AS3360 is a dual general purpose voltage controlled transconductor intended for such applications as voltage controlled amplifiers, filters, and waveform generators. Each transconductor independently provides both linear and exponential control scaling over greater than a 100 dB range. Complete with virtual ground summing inputs, wide voltage compliance current outputs, and control inputs referenced to ground, the AS3360 requires exceptionally few external components and is extremely easy to use. Because of its inherent ultra-low control feedthrough, no trimming is required.
P-QOP275 Op-Amp - OP275, Dual, Bipolar/JFET, Audio, 8-Pin DIP
OP275 dual audio op amp in an 8-pin DIP package. The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortion plus Noise equals that of previous audio amplifiers, but at much lower supply currents. A very low l/f corner of below 6 Hz maintains a flat noise density response. Whether noise is measured at either 30 Hz or 1 kHz, it is only 6 nVHz. The JFET portion of the input stage gives the OP275 its high slew rates to keep distortion low, even when large output swings are required, and the 22 V/µs slew rate of the OP275 is the fastest of any standard audio amplifier.
P-QCD4007 CMOS - CD4007, Dual Complementary Pair Plus Inverter, 14-Pin DIP
CD4007UB types are comprised of three n-channel and three p-channel enhancement-type MOS transistors. The transistor elements are accessible through the package terminals to provide a convenient means for constructing the various typical circuits as shown in Fig. 2. More complex functions are possible using multiple packages. Numbers shown in parentheses indicate terminals that are connected together to form the various configurations listed. Features:
  • Standardized symmetrical output characteristics
  • Medium Speed Operation — tPHL, tPLH = 30 ns (typ.) at 10 V
  • 100% tested for quiescent current at 20 V
  • Meets all requirements of JEDEC Tentative Standard No.
Don't see what you're looking for? Send us your product suggestions!