Sorry! You are trying to check out one of our items which is no longer available. Why not check out one of these alternate options?
Effects Pedal Kit - MOD® Kits, The Thunderdrive, Overdrive
The Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction. This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours. All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.
Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost
"The Piledriver" is a clean-boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!
Effects Pedal Kit - MOD® Kits, The Tea Philter, T Filter
A T-Filter Pedal Kit - the Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.
Kit - Pine Board Power Supply with 3 Outputs
Input - 120V, 60 Hz. "A" Output - Adjustable and regulated 1.5 to 7.5 volts 1.5 Amps "B" Output - 22, 45, 67, 90, and 135 volts regulated up to 50mA. "C" Output - Adjustable 0 to 22 volts. Regulated. Kit includes transformer, rectifiers, capacitors, resistors, transistors, I.C., regulator, white pine board, and all necessary hardware. Easy to follow instructions for assembly.
Effects Pedal Kit - MOD® Kits, The Contortionist II, Fuzz
The Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.
Effects Kit - MOD® Kits, The Wave, Spring Reverb
The Wave is a versatile stand-alone, tube driven analog spring reverb unit kit. It can be used in front of your guitar amp or as a line-level analog reverb effect for the recording studio. Two controls allow you to serve up a wide range of wetness from just a touch to over the top psychedelia. The "dwell" control adjusts the input signal level driving the tank and the "reverb" control adjusts the level of output reverberations from the tank. The Wave's all tube design utilizes four dual triode vacuum tubes - three 12AX7s and one 12AT7 - and comes with a MOD® three-spring reverb tank. MOD® reverb tanks are deemed the closest to the original reverb tanks from the '60s made today. The Wave's reverb function can be switched in and out pop-free via the front panel toggle or with a footswitch. Footswitch sold separately (see P-H470 for compatible footswitch).
Effects Pedal Kit - MOD® Kits, The Penetrator, Treble Boost
The Penetrator is a treble boost pedal kit with enough gain to cut straight through any mix. This pedal adds glistening harmonics that get loud enough to saturate your amp’s front end. Adjust the level knob to vary the output so there’s no mistaking when you kick this pedal in. Great for solos or when you need your guitar front and center.
Effects Pedal Kit - MOD® Kits, The Persuader Deluxe, Overdrive
The Persuader Deluxe utilizes a Darlington preamp to push cascaded triode vacuum tubes into distortion. Four dual triode vacuum tubes are included with each kit (JJ 5751, 12AX7B China, JJ 12AU7 and a NOS USA-made 12AT7). Swap to create a wide range of tones from just a hint of break up from the JJ 5751 to over the top crunchy distortion using the NOS US made 12AT7. A boost switch provides an additional layer of flexibility with added gain and a little extra bottom end. An LED indicator lights up when the Persuader Deluxe is engaged and not in true bypass mode. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
Effects Pedal Kit - MOD® Kits, The Trill Tremolo
The Trill Tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.
Effects Pedal Kit - MOD® Kits, The Persuader, Tube Drive
Build your own tube preamp pedal built around a 12AX7 tube. Go from clean, warm tone to smooth, real tube overdrive. This kit includes pre-drilled die-cast aluminum enclosure and all parts with easy to follow instructions.