You are here

Holiday Gifts

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(15 pages)
S-T202Understring Radius Gauges - 9 Sizes, for Saddle Adjustments
Our low profile aluminum understring radius gauges have a precision radiused top and bottom for accurate measurement. The slim shape allows you to take measurements of several radii without removing the strings on your guitar.

  • Obtain accurate measurements of your instrument's fretboard radius using the bottom radius of the gauge. The bottom radius can also be used to set pickup polepiece height to the string radius.
  • Use the top radius of this gauge to determine the proper height adjustment for the bridge saddles.
  • The following gauges are included in this set: 7.25" 9.5" 10" 12" 14" 15" 16" 17" 20"
$14.00
Click to read more
S-T227Radius Gauges - 2 Gauges for 8 Radiuses
Solid, high quality stainless steel radius gauges. Use during fingerboard/fret shaping to accurately measure your progress and eliminate mistakes. Can also be used when shaping a nut/saddle or when setting string radius at the bridge. Great for working on compound radius necks. This is an essential tool for a luthier/tech’s bench.

  • Gauge 1 has 7.25", 9.5", 10", and 12" radiuses
  • Gauge 2 has 14", 15", 16", and 20" radiuses
  • Set of 2
$14.00
Click to read more
K-950Effects Pedal Kit - MOD® Kits, The Thunderdrive, Overdrive
The Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction.
This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours.
All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.
$29.95
Click to read more
B-707How to Service Your Own Tube Amp by Tom Mitchell
A well organized and easy-to-understand approach to guitar amplifier repair covering basic electronics, reading schematics, understanding tubes and transformers, tube biasing and use of test equipment. Also provides 10 troubleshooting flowcharts, voltage charts for typical amplifiers, and many modifications that you can do yourself.
250 pages, 2.3 lbs, 8.5" x 11"
$27.50
Click to read more
K-920Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost

"The PileDriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!


$24.95
Click to read more
K-955Effects Pedal Kit - MOD® Kits, Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe is an overdrive pedal kit that will provide a strong clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting volume control and gain controls provides a wide variety of tones in spite of it's simple contruction.
The Turbo switch provides an additional boost in volume and less internally generated distortion. The pre-painted black enclosure, red control knobs and red LED indicator give the Thunderdrive Deluxe an understated attractive finish. It is capable of overdriving the preamp section of your guitar amp or adding it's own layer of distortion at lower volume.
This is an easy build kit with point to point wiring and clear, easy to follow instructions. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life. All you need to provide is solder, soldering iron and a few simple tools.
$39.95
Click to read more
K-930Effects Pedal Kit - MOD® Kits, The Persuader, Tube Drive
Build your own tube preamp pedal built around a 12AX7 tube. Go from clean, warm tone to smooth, real tube overdrive.
This kit includes pre-drilled die-cast aluminum enclosure and all parts with easy to follow instructions. All you need to provide is solder and soldering iron.
The Persuader allows for easy access to the tube, giving you the ability to quickly experiment with different tube brands and 12AX7 tube relatives.
Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$64.95
Click to read more
P-YJRSolid State Tube Rectifier - Yellow Jackets®, YJR

The YJR is a direct plug-in replacement adapter for use in most amplifiers that use 5AR4/GZ34, 5U4, 5Y3 or similar full-wave rectifier tubes. The YJR converts your amp’s vacuum tube rectifier to a solid state rectifier, reducing tube sag for a tighter sound and feel. The tube rectifier can easily be swapped back in when sag is desired. This Yellow Jacket® is a solid state device and as such does not come with vacuum tubes.



  • Converts most audio amplifiers which use a vacuum tube rectifier 5AR4/GZ34, 5U4 or 5Y3 to a solid state device.
  • Safe for all common amplifiers and transformers.


Note: Because there is no warm up of a rectifier tube when using this solid state device, it is critical that a standby switch is used that will allow the power tube filaments to warm up before high voltage is applied.


$14.95
Click to read more
K-101AKit - Power Supply

Input - 120V, 60 Hz. "A" Output - Adjustable and regulated 1.5 to 7.5 volts 1.5 Amps "B" Output - 22, 45, 67, 90, and 135 volts regulated up to 50mA. "C" Output - Adjustable 0 to 22 volts. Regulated. Kit includes transformer, rectifiers, capacitors, resistors, transistors, I.C., regulator, white pine board, and all necessary hardware. Easy to follow instructions for assembly. 3.0 lbs.


$54.95
Click to read more
S-T203String Spacing Ruler - Steel

Get accurate string spacing without the use of complicated tools with this easy-to-use String Spacing Ruler. "Mark outer string locations with pencil lines (high and low E strings on guitars), usually about 1/8" in from fingerboard edges. Turn ruler over (use marked side). With wide spacing toward bass side, narrow spacing toward treble side, find group of marks (six for guitar) which best fit your two pencil lines. Use a razor knife or thin mechanical pencil to mark the string positions through the ruler's slots.


$19.95
Click to read more

Pages

(15 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Holiday Gifts