Hardware

Knurled, slotted nut for W-QP-419GR and W-QP-518MA 3.5mm jacks.
See W-QP-NUT-H for the hex version of this nut.
See W-QP-WASHER for compatible washer

Hex nut for W-QP-419GR and W-QP-518MA 3.5mm jacks.
See W-QP-NUT-K for the knurled, slotted version of this nut.
See W-QP-WASHER for compatible washer

Replacement nut for Marshall style pots with 7mm bushing. Sold individually

Zinc nut. Designed to be used with any low carbon bolt or screw such as a grade 2 bolt. Most commonly used nut. Achieves strength through cold forming. Low carbon steel.

Replacement nut for CTS 450 series potentiometers and others.

• 3/8-32 threading
• Sold individually

Hex nut for Carling switches, 15/32". Sold individually.

A threaded fastener made from austenitic stainless steels. It contains chromium creating an invisible surface film that resists oxidation making the metal corrosion resistant. If the surface layer is damaged, it rebuilds itself in the presence of oxygen.

Nut - Hex, for Cliff UK Jacks S-H902, S-H903, S-H904, & S-H905

Red Cliff hex nut, often used on guitar amplifiers to identify loudspeaker outputs.

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 10-24 Threading
• Panel Range .064-.105
• Zinc Finish
• Sold Individually

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 8-32 Threading
• Panel Range .064-.105
• Zinc Finish

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 10-32 Threading
• Panel Range .064-.105
• Zinc Finish
• Sold Individually

Replacement nut and washer for pots with a ⅜" bushing diameter.

Replacement nut for Marshall snap in style pots with M9 bushing.

Hex nut for white Cliff Jacks, threading: 7/16-20. Also used on the footswitch jack in some Marshall amps.

Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These dress nuts feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is capped. These fit any 15/32-32UNS bushing but can also work with M12 bushings.

Nut - Keps with external tooth, Zinc, fits screws for chassis straps, 8-32 X 3 1/4, package of 10. Popular low-cost lock nut for commercial and industrial applications. Locking action is achieved when the nut is tightened against a bearing surface as the teeth of the lock washer dig into it.

Nickel-plated steel finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. These high quality washers closely resemble the washers found on many vintage blackface and silverface amplifiers. Fits with #8 countersunk screws.

Popular low-cost lock nut (also known as a Keps nut, k-lock, or washer nut) for commercial and industrial applications. Locking action is achieved when the nut is tightened against a bearing surface as the teeth of the lock washer dig into it.

Zinc t-nut. Used for fastening metal to products made of wood, particle board or plastic. Low carbon steel. Package of 5. Multiple sizes available.

M8 x 0.75 threaded hex nut. For use on potentiometers, switches, and jacks.

300V wire nuts for use with 18 gauge through 22 gauge wires. These wire nuts are great for use on appliances, televisions, stereos, antennas, or for any small wiring application. Rated for up to 105°C.

M12 x1.0 threading. Nut and washer set for panel-mounting jacks.

Original Switchcraft Copper Alloy Knurled Locknut (Nickel Plated)
Outside Diameter:5/8"
Inside diameter threading:15/32"
Width: 3/32"