Hardware

S-H131 Screws - Original Fender, Vintage Style Strat Bridge Mounting
Genuine Fender® vintage-style Strat bridge mounting screws. Some of Fender’s most requested replacement screws. Made for Fender® and used on a variety of vintage and contemporary models.
  • Set of 12 replacement screws
  • Genuine vintage specifications
  • Nickel plating
  • Phillips oval-head (#6 x 1 1/8")
  • Used on American Vintage Stratocaster® guitars
$3.25
package of 12
P-GGT-87-C Ferrules - Gotoh, TLB-1, for Guitar, Chrome
The Gotoh TLB-1 is a high quality set of guitar string ferrules. These press fit ferrules are a great choice for Telecaster® guitars or any guitar with a string through bridge. Includes six ferrules.
$4.25
package of 6
P-H183 Washer - Rubber, Chassis Mount, 1-⅛" x ¼" Thick
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.
$2.15
S-HNFW-M3-X Washer - Flat, M3, Nylon, for Front Panels
Colors Available:
High quality nylon M3 flat washers. These durable washers fit perfectly on M3 threaded screws. The small outside diameter provides a clean look beneath the head of the screw. These are great mounting washers for preventing rack rash on front panels like Eurorack synths or any other use where the surface beneath the screw requires protection.
$0.99
package of 10
S-H101 Screw - #6 x ¾", Pan Head, Stainless Steel
Stainless steel pan head Phillips self-tapping screws. #6 X ¾" length. Good for use with #'s 3,4 and 5.
$4.35
package of 12
S-HMB-JEN Bracket - for PCB mounting, replica of Vintage Fuzz
Mounting bracket for vintage fuzz PCBs. This bracket is an exact replica of the bracket found in the Italian made Vox Tone Bender V828 pedals. The mounting width for the board is 1.35” which fits the P-PC-FUZZ-JEN, P-PC-BEND-MKII-BRN, and any other vintage spacing (0.15”) stripboard. The PCB mounting holes are threaded for M3 screws (sold separately). The two potentiometer holes are spaced 1.95” center to center and fit potentiometers with ⅜” bushings or smaller.
$5.95
S-HS1032-X Screw - 10-32, Phillips, Pan Head, Machine, Zinc, fine thread
Phillips panhead machine screw, 10-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
Starting at $1.15
package of 5
S-H130 Screws - Original Fender, Vintage Speaker Mounting Stud / Nut
Original Fender speaker mounting stud/nut set. These speaker mounting studs were used on countless amps of the '50s, '60s, '70s, and beyond. The reverse thread section screws into the baffle wood and the machine screw section holds the speaker in place using the included keps nuts.
  • Used on early ’50s and ’60s vintage amplifiers
  • Fits most vintage and modern amplifiers
  • 1” of 8-32 machine head thread
  • ¼” of reverse wood thread
  • 1-½” overall length
  • 8-32 keps nuts included

Fender part number: 099-2094-000
$8.95
package of 12
S-H119 Screws - Fender®, Saddle Height Screws
Set of hex set screws used for saddle-height adjustment on American Vintage series Stratocaster and Telecaster bridges.
  • Set of 12 hex set screws
  • For American Vintage Stratocaster and Telecaster guitars
  • Comes with four 4-40 x 3/8" hex screws and eight 4-40 x 5/16" hex screws.
$4.95
package of 12
P-H52-DRESS-WIDE Nut - Wide Dress Nut, Threaded Through, 15/32-32UNS
Wide dress nuts for use with full size toggle switches and footswitches. These dress nuts feature a wide chamfered edge that pairs nicely with smaller dress nuts such as P-H54-DRESS-WIDE, P-H54-DRESS-THRU, and P-H54-NUT-DRESS. These nuts are threaded through and fit any 15/32-32UNS bushing such as Carling footswitches and full sized toggles.
$1.75
S-HBR-18D-X Blind Rivet - Dome Head, Steel, ⅛ in. diameter
Steel shank / steel mandrel blind rivets with a ⅛” diameter. Blind rivets, also referred to as pop rivets, can be used to join or fasten two components without requiring access to the backside of the panel or chassis. The installation is quick and results in a joint that can be stronger and tighter than a screw. These rivets are useful for securing tube sockets or other hardware such as battery holders on stompboxes.
Starting at $1.15
package of 12
S-HSB4-X Screw - 4-40, Phillips, Round Head, Machine, Brass
4-40 Phillips round head machine screws made of solid brass. These brass round head screws visually match the screws found on vintage Marshall amplifiers. They are a great choice for restoration or replica builds. The 4-40 size works in place of original M3 screws that were used for the AC inlet, noval sockets, PCB and turret board standoffs, and the P-H1700 and S-HM100-A rotary selectors. These will also work well in many other types of projects. Brass round head screws are available in the following sizes: Diameter/TPI SKU 4-40 S-HSB4-X 6-32 S-HSB6-X 8-32 S-HSB8-12 Pairs with S-HBNX brass nuts and S-HLWX-B lock washers. Use with S-ASP4-X spacers for board standoffs. S-HBWX flat washers are also available.
Starting at $1.59
package of 5
S-M560 Insulation - GC Electronics, fibroid, "fish paper"
Vulcanized Cellulose Fiber for all electrical insulation. Gray insulating paper. .010" thick. used in switches, under terminals, in transformers, etc .where mechanical strength is required. Its qualities of toughness, flexibility, and edge-tearing resistance combined with high dielectric strength and ready absorption of insulating varnish have led to its predominant use as an improved motor slot call insulation. Dielectric strength 3000 volts. 10" wide roll contains 240 sq. inches.
$6.25
P-H185 Washer - ⅞" x ⅛" Thick, Rubber, Chassis Mount,
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Adhesive backing for lamenating to other washers to increase thickness. Overall dimensions 7/8" dia. x 1/8" thick.
$0.65
S-HCN832 Nut - Cage, Zinc, 8-32, Electroplate Panel Range .064-.105
Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.
  • 8-32 Threading
  • Panel Range .064-.105
  • Zinc Finish
$0.75
P-H52-NUT-PLX Nut - Large Dress Nut, Carling, 15/32-32UNS, Plastic
Colors Available:
Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These nuts are made of a strong durable plastic and feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is not capped so they can thread past the top of the bushing. These fit any 15/32-32UNS bushing but can also work with M12 bushings.
Starting at $0.75
S-H4FW-X Finishing Washer - #4, Countersunk
#4 finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance.
Starting at $1.35
package of 10
S-H107 Screw - Fender®, for Pickups and Switches
Original Fender 6-32 screws for use on pickups and switches.
$4.45
package of 12
S-HCN-M6 Nut - Cage, Zinc-plated Steel, M6, Panel Range .064-.105”
Common replacement for Marshall heads and many other applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening. Fits panels 0.064" to 0.105" thick with square holes cut 0.375" to 0.38".
  • M6 Threading
  • Panel Range .064”-.105”
  • Fits 0.375" to 0.38" Square Holes
  • Zinc Finish
  • Sold Individually
$1.39
S-H111 Nut - Hex, for Carling switches, ~\frac{15}{32}~"
Hex nut for Carling switches, 15/32". Sold individually.
$0.40
S-H9NT-M Nut - Cliff, Hex, Plated Steel
Hexagonal, plated steel nut for Cliff UK jacks. This nut fits Cliff jacks with 7/16″ UNF, 20 TPI threading.
$0.65
P-GTF-N Ferrules - Fender®, for Original Telecaster, nickel, set of 6
Fender® replacement string ferrules for Original Tele (6 ferrules)
$8.75
package of 6
S-HPOH6-X Screw - #6, Phillips, Oval Head, Wood, Nickel-plated
#6 Phillips drive wood screws made of nickel plated steel. This style of oval head screw is commonly used on Fender® tweed, blackface, and silverface combos and heads to secure the back panel. They are also the same type used for securing strap buttons as well as for mounting the bridge plate on Telecaster® guitars.
Starting at $1.25
package of 4
S-HRS6-114 Screw - #6-32 x 1 ¼” Rosette Head, Machine, Bronze-plated
#6-32 x 1-¼” machine screws made of bronze plated steel. This style of rosette head screw is similar to the baffle mount screws found on many early Fender® tweed amplifiers. For an 8-32 rosette head screw, see S-HRS8-1116.
$1.89
package of 4
Don't see what you're looking for? Send us your product suggestions!