Hardware

Phillips panhead machine screw, 10-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These nuts are made of a strong durable plastic and feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is not capped so they can thread past the top of the bushing. These fit any 15/32-32UNS bushing but can also work with M12 bushings.

Zinc t-nut. Used for fastening metal to products made of wood, particle board or plastic. Low carbon steel. Package of 5. Multiple sizes available.

Phillips panhead machine screw, M3 metric, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
See S-HS-M3-6-X for colored 6mm M3 screws.

Switchcraft shouldered hex nuts for ⅜”-32 UNEF-2A threaded bushings. These nuts include a rubber grommet for use in sealed systems and also add a unique look to any build such as pedals or amplifiers. The large nut (W-SC-DRESS-1) is intended for panel or chassis thicknesses of 0.05” through 0.09”. The small nut (W-SC-DRESS-2) is intended for panel or chassis thicknesses of 0.095” through 0.125”. Rubber grommet included.

20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:

• Round Pin
• 20 Position
• 2.54mm Spacing
• Breakaway

Self tapping Phillips panhead machine screw #8, zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but not necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.

#6 x 3/8 zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.

Genuine Switchcraft ⅜” knurled nut commonly used on ¼” jacks. This nickel plated knurled nut has a ⅜”-32 threading and offers a clean look on builds using these nuts. The ⅜”-32 threading fits other hardware with matching threading such as CTS potentiometers.

M12 x1.0 threading. Nut and washer set for panel-mounting jacks.

High quality nylon M3 flat washers. These durable washers fit perfectly on M3 threaded screws. The small outside diameter provides a clean look beneath the head of the screw. These are great mounting washers for preventing rack rash on front panels like Eurorack synths or any other use where the surface beneath the screw requires protection.

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 8-32 Threading
• Panel Range .064-.105
• Zinc Finish

Oversized M12 flat washers. These washers fit both metric (M12) and imperial (15/32) bushings for compatibility with the vast majority of foot switches and full-sized toggle switches. These oversized washers are a great way to add a distinctive look to projects.

Genuine Fender® vintage-style Strat bridge mounting screws. Some of Fender’s most requested replacement screws. Made for Fender® and used on a variety of vintage and contemporary models.

• Set of 12 replacement screws
• Genuine vintage specifications
• Nickel plating
• Phillips oval-head (#6 x 1 1/8")
• Used on American Vintage Stratocaster® guitars

Flat-washer style solder tag for use with M3.5 or #6 screws. This small solder tag is an easy way to add a wire such as a chassis ground connection to a build. This solder tag is also a great match for vintage style builds such as Fuzz Face style effects pedals.

• Contact Material: Brass
• Contact Plating: Tin
• Inner Diameter: 3.5± 0.2 mm
• Outer Diameter: Ø6.3 ± 0.2 mm
• Length: 12.7 ± 0.5 mm
• Thickness: 0.35 mm

Nylon flat washers for use with foot switches. These washers are M12 size and fit both metric (M12) and imperial (15/32) bushings for compatibility with the vast majority of foot switches.

#4 finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance.

#10 steel finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. Made of 18-8 stainless steel.

Original Fender speaker mounting stud/nut set. These speaker mounting studs were used on countless amps of the '50s, '60s, '70s, and beyond. The reverse thread section screws into the baffle wood and the machine screw section holds the speaker in place using the included keps nuts.

• Used on early ’50s and ’60s vintage amplifiers
• Fits most vintage and modern amplifiers
• 1” of 8-32 machine head thread
• ¼” of reverse wood thread
• 1-½” overall length
• 8-32 keps nuts included

Fender part number: 099-2094-000

M8 x 0.75 threaded hex nut. For use on potentiometers, switches, and jacks.

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 10-24 Threading
• Panel Range .064-.105
• Zinc Finish
• Sold Individually

A threaded fastener made from austenitic stainless steels. It contains chromium creating an invisible surface film that resists oxidation making the metal corrosion resistant. If the surface layer is damaged, it rebuilds itself in the presence of oxygen.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Adhesive backing for lamenating to other washers to increase thickness. Overall dimensions 7/8" dia. x 1/8" thick.