Guitar Parts & Pickups
Guitars can lead a rough life and replacement parts can bring your axe to like new condition. But did you know that you can also change components to achieve different sounds? The options are endless!

Includes all parts but the magnet wire, all sets are ready for winding. Kits include Alnico 5 magnets, bobbins, poll screws, slug screws, baseplate, and coil lead wires. These pickups use alnico 5 pole pieces to produce a warm, well rounded classic tone.
Starting at $15.95

Package of 12
This spring helps set your tremolo arm in a fixed position when used with any Fender® American series or American Standard series tremolo. Simply insert spring into tremolo arm receptacle prior to installing tremolo arm. Package includes twelve tension springs. Used in Custom Shop, American Series, American Vintage, American Standard (USA), and Classic, Deluxe, and Road Worn® Series (Mexico) instruments.
$6.95

Colors Available:
$7.95

Package of 24
Original Fender pickguard screws. Set of 24 Phillips head screws (4x1/2") for pickguard and control plate mounting on most Fender instruments.
Starting at $4.25

The V-Treb Variable Treble Bleed Circuit attaches to the bottom of any volume pot and corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound.
$10.35

Package of 5
Phillips panhead machine screw, 10-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
Starting at $1.05

Strat style 4 bolt neck plate. (Mounting hardware not included). Four ¼” mounting holes. Made in Korea
$7.25

Package of 6
Colors Available:
Starting at $35.95

Package of 2
Colors Available:
Starting at $2.75

Package of 6
Colors Available:
Starting at $16.95

Alnico cast bar magnets for use in humbucker and P-90 pickups. These are fully magnetized through the width and measure 2.444” x .5” x .125”.
$4.25

Gibson style top hat knob. Fits fine knurled pot shafts.
$2.25

Genuine Dunlop replacement small knurled knob for MXR pedals. Push -on style knob designed for use with coarse knurled shafts.
$3.67

Colors Available:
Starting at $9.65

Colors Available:
Starting at $24.20

Genuine Dunlop replacement knob cover for smaller control knobs found on many MXR pedals. This knob cover is also compatible with our P-K344 control knob.
$1.83

Package of 5
Self tapping Phillips panhead machine screw #8, zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but not necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.
Starting at $0.72

Colors Available:
Starting at $6.54

Colors Available:
Starting at $104.60

Bone nut for Gibson®, 43mm x 5.9mm x 8mm at highest point with flat bottom.
$5.55

Package of 2
Colors Available:
Starting at $13.39

Colors Available:
Starting at $44.95

Colors Available:
$1.50

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm at highest point with flat bottom.
$3.95