Guitar Parts & Pickups

Original Fender pre-slotted bone nut for Teles and Strats.

LSR roller nut reduces friction that can cause tuning instability. Comes with instructions, mounting hardware and Wilkinson® adapter for older Strat® Plus models. Used on American Deluxe HSS guitars. Kit Includes: LSR Nut, Shims, Mounting Screws and Bezel Adapter (for Retrofitting to Wilkinson® Nut Equipped Guitars) Will Accommodate String Gauges from .008 to .056. Some modification may be required.

Blank string nuts for Fender® guitars made of plastic

Plastic strat guitar nut.

Graphite nut for Fender® This graphite nut will work for most Fender® and similar style guitars. It is slotted, but does require final shaping and fitting to exact size.
PLEASE NOTE: Because this nut tapers in both thickness from top to bottom and height on the fret board side vs. the headstock side all measurements for those dimensions were taken at the center of the nut.

• Length = 1 41/64 inches (41.52mm)
• Height #1 (fretboard side) = 13/64 inches (5.06mm)
• Height #2 (headstock side) = 13/64 inches (5mm)
• Thickness at bottom = 9/64 inches (3.46mm)
• Thickness at top = 1/8 inches (3.1mm)

Bone nut for Gibson®, 43mm x 5.9mm x 8mm at highest point with flat bottom.

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm with radiused bottom.

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm at highest point with flat bottom.

This graphite nut will work for most Gibson® and similar style guitars and basses. It is slotted but does require final shaping and fitting to exact size.
PLEASE NOTE: Because this nut tapers in both thickness from top to bottom and height on the fret board side vs. the headstock side all measurements for those dimensions were taken at the center of the nut.

• Length = 1 23/32 inches (43.75mm)
• Height #1 (fretboard side) = 5/16 inches (7.81mm)
• Height #2 (headstock side) = 9/32 inches (7mm)
• Thickness at bottom = 15/64 inches (6.1mm)
• Thickness at top = 3/16 inches (4.78mm)

Fender® replacement string nut for American Standard Precision Bass

This brass nut blank will work for most Fender® and similar style guitars and basses. It is NOT slotted and does require final shaping and fitting to exact size.

• Thickness = 9/64 inches (3.47mm)
• Flat Bottom Length = 1 11/16 inches (43 mm)
• Height at ends = 13/64 inches (5.25mm)
• Height at middle = 15/64 inches (6mm)

This graphite nut blank will work for most Fender® and similar style guitars and basses. It is NOT slotted and does require final shaping and fitting to exact size. It has a radiused bottom.

• Length = 2 1/64 inches (51.25mm)
• Height = 11/64 inches (4.55mm)
• Thickness = 1/8 inch (3.1mm)

Plastic electric guitar nut.

Original Fender pre-slotted melamine nut for Teles and Strats.

The Zero Glide® Replacement Nut System borrows the “zero fret” concept to reduce string contact in the nut by up to 93%, increasing tuning stability, playability, and open string tone. It only take a few minutes to install with absolutely no permanent alteration to your instrument. Zero fret wire included (multiple sizes). Comparison Standard Nut Zero Glide Open String Tone Absorbs energy. Fret reflects energy, making the open strings more vibrant. Tuning Friction causes string binding. 93% less surface area. More accurate tuning. String Bend/Whammy Bar Whammy bars and string bends cause the strings to bind in the nut and not return to pitch Reduces string binding and "returns to zero" after every tug of the whammy bar or bend Intonation Large pitch deviation in early frets. (See intonation graph below) Minimal pitch deviation in early frets.

The Zero Glide® Replacement Nut System borrows the “zero fret” concept to reduce string contact in the nut by up to 93%, increasing tuning stability, playability, and open string tone. It only take a few minutes to install with absolutely no permanent alteration to your instrument. Zero fret wire included (multiple sizes). Comparison Standard Nut Zero Glide Open String Tone Absorbs energy. Fret reflects energy, making the open strings more vibrant. Tuning Friction causes string binding. 93% less surface area. More accurate tuning. String Bend/Whammy Bar Whammy bars and string bends cause the strings to bind in the nut and not return to pitch Reduces string binding and "returns to zero" after every tug of the whammy bar or bend Durability Slots wear down over time. Minimal wear.

High-quality solid-brass string nut as used on the Yngwie Malmsteen Stratocaster®, for use with Stratocaster and Telecaster® guitars. Designed for 9.5"-radius fingerboards and pre-slotted with string location grooves to simplify spacing and positioning during final slot filing. Note that some filing and shaping modifications may be required to ensure proper fit and performance. • High-quality solid-brass string nut • For 9.5" fingerboard radius • Pre-slotted • 9.5" (241mm) top and bottom radius • 1.620” (41.15mm) wide

High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom feel and appearance.

• Measures 45mm x 10mm x 4.95mm
• Sold individually

High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom fit and appearance.

• Measures 52.5mm x 10mm x 4.95mm
• Sold individually

High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom fit and appearance.

• Measures 56 mm x 11 mm x 6.35 mm
• Sold individually