Guitar Parts & Pickups

Tele style control plate in chrome. 5 3/8” plate mounting center distance (0.12” diameter, recessed).

• Two potentiometer mounting holes for 3/8” bushing diameters
• One standard selector switch mounting slot (1.63” mounting center distance, 0.15” diameter, recessed)

Made in Korea

Tremolo tension springs. Similar to P-GTSPRN-5 but generic manufacture.

This modern cupstyle Tele® jackplate is milled from brass and has an shiny plated finish. Mounts with (2) screws that are included. No more having to deal with that sharp piece of steel used to secure the old original cups. Super easy to install! The cup is even threaded so no need for the lockwasher and nut from the jack. Just simply screw the jack into the cup, solder the wires and install into your instrument!

Jaguar style master control plate in chrome. Perfect replacement for most Jaguar style guitars. 4.12” x 1.86” plate mounting center distance (0.14” diameter, recessed).

Standard (4-hole) and vintage (3-hole) versions. Replacement for most Jazz Bass style guitars. Made in Korea.

Replacement jack plate for Stratocasters

Strat style 3 ply pickguard with 11 mounting holes. Top and bottom layers are the same with an alternate middle layer.

Three-ply black/white/black ’62 Tele style pickguard with 8 mounting holes. This pickguard has no pickup mounting holes for use with neck pickups that mount directly to the guitar’s body.

5-way switch for Strats, black tip.

Strat style 4 bolt neck plate. (Mounting hardware not included). Four ¼” mounting holes. Made in Korea

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm with radiused bottom.

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm at highest point with flat bottom.

This brass nut blank will work for most Fender® and similar style guitars and basses. It is NOT slotted and does require final shaping and fitting to exact size.

• Thickness = 9/64 inches (3.47mm)
• Flat Bottom Length = 1 11/16 inches (43 mm)
• Height at ends = 13/64 inches (5.25mm)
• Height at middle = 15/64 inches (6mm)

Retrofit your USA '67-'82 Fender P & J Bass for drop tuning! Also retrofits Geddy Lee, reissue '67-'82 Fender. Fits 11/16 in. headstock holes. Installation instructions and mounting hardware included.

Tremolo Arm, Screw-Down, Steel 5mm-0.8p

• Material: Steel 5mm
• Handle Type: Screw-down
• Thread: M5.0 - 0.8p
• Plating: Chrome
• Tip: White

Graphite nut for Fender® This graphite nut will work for most Fender® and similar style guitars. It is slotted, but does require final shaping and fitting to exact size.
PLEASE NOTE: Because this nut tapers in both thickness from top to bottom and height on the fret board side vs. the headstock side all measurements for those dimensions were taken at the center of the nut.

• Length = 1 41/64 inches (41.52mm)
• Height #1 (fretboard side) = 13/64 inches (5.06mm)
• Height #2 (headstock side) = 13/64 inches (5mm)
• Thickness at bottom = 9/64 inches (3.46mm)
• Thickness at top = 1/8 inches (3.1mm)

Replacement jack plate for Telecasters

Jaguar style preset control plate in chrome. Perfect replacement for most Jaguar style guitars. 4.57” x 1.79” plate mounting center distance (0.14” diameter, recessed).

Replacement pickguard for Fender® '57 Strat® models. These single ply pickguards have eight mounting holes. Cut from a thicker single ply sheet, these pickguards offer a vintage style with added rigidity. Fits most American, Japanese, and Mexican '57 Stratocasters®.

Replacement pickguard for Fender® Standard Strat® models. These pickguards have eleven mounting holes and are cut for the classic strat® configuration. Fits most American and Mexican Standard Stratocasters®. Features:

• 3-ply / 2.5mm thickness
• 11 mounting holes
• Shielding over electronics cavity
• Fits 3/8" bushing pots
• Various colors available

Three-ply black/white/black Strat style back plate with 6 mounting holes.

Replace your sloppy, worn out tuning machines with a set of Hipshot American Classics. The HB2 is a direct replacement for the Schaller® BMF tuner that was first found on CBS era Fender® basses manufactured between 1967 and 1982. Since then, the BMF tuner has been featured on countless boutique builds and Custom Shop models.

Plastic strat guitar nut.

These pickguards have eleven mounting holes and feature cutouts for two single coil pickups and a humbucker in the bridge position. The humbucker cutout has rounded corners for a flush fit with uncovered pickups.