Enclosures / Chassis

Fender® style narrow panel Tweed Deluxe™(5E3) chassis.
*NOTE*- This chassis has replaced the “ground” switch lettering found on originals with “standby”
- Chrome plated steel, .06" thick.
- Screened white lettering
- 8-Pin (Octal) socket holes: 3
- 9-Pin (miniature) socket holes: 2
- Chassis Dimensions: 14 1/2" x 4 1/8" x 2 5/8"
*NOTE*- This chassis has replaced the “ground” switch lettering found on originals with “standby”
$68.53

Fender® style Tweed Champ™(5F1) chassis.
- Chrome plated steel, .06" thick.
- Screened white lettering
- 8-Pin (Octal) socket holes: 2
- 9-Pin (miniature) socket holes: 1
- Chassis Dimensions: 8-3/4" x 4-1/8" x 2 5/8"
$56.07

Fender® style narrow panel Tweed Princeton™(5F2) chassis.
- Chrome plated steel, .06" thick.
- Screened white lettering
- 8-Pin (Octal) socket holes: 2
- 9-Pin (miniature) socket holes: 1
- Chassis Dimensions: 13-3/4" x 4-1/8 x 2-1/2"
$62.30

Fender® style narrow panel Tweed Bassman™(5F6A) chassis.
- Chrome plated steel, .06" thick.
- Screened white lettering
- 8-Pin (Octal) socket holes: 3
- 9-Pin (miniature) socket holes: 3
- Chassis Dimensions: 20'' x 4 1/8'' x 2 5/8''
$74.76

Marshall™ style 18 Watt TMB chassis w/ front and back plates
Chassis Measurements:
Compatible Part Links:
- Brushed aluminum chassis, .07" thick.
- Gold “plexi” style front and back plates
- 9-Pin (miniature) socket holes: 6
- Capacitor mounting holes:1
- Chassis Dimensions(without mounting flange): 17" x 6-½" x 2-½"
Chassis Measurements:
- Power transformer mounting centers: 3-1/8” x 2-1/2”
- Output transformer mounting centers: (#1) 3-3/16” (#2)3-11/16”
- Can cap mounting centers : 2”
- Noval (9-pin) tube sockets: 1-1/8”
Compatible Part Links:
- Noval socket with shield base: P-ST9-700
- Noval socket (no shield): P-ST9-600
$88.47

Marshall™ style 18 Watt Tremolo chassis w/ front and back plates
Chassis Measurements:
Compatible Part Links:
- Brushed aluminum chassis, .07" thick.
- Gold “plexi” style front and back plates
- 9-Pin (miniature) socket holes: 6
- Capacitor mounting holes:1
- Chassis Dimensions(without mounting flange): 17" x 6-½" x 2-½"
Chassis Measurements:
- Power transformer mounting centers: 3-1/8” x 2-1/2”
- Output transformer mounting centers: (#1) 3-3/16” (#2)3-11/16”
- Can cap mounting centers : 2”
- Noval (9-pin) tube sockets: 1-1/8”
Compatible Part Links:
- Noval socket with shield base: P-ST9-700
- Noval socket (no shield): P-ST9-600
$88.47

Marshall™ style JTM45 chassis w/ front and back plates
Chassis Measurements:
Compatible Part Links:
- Brushed aluminum chassis, .07" thick.
- Gold “plexi” style front and back plates
- 8-Pin (Octal) socket holes: 3
- 9-Pin (miniature) socket holes: 3
- Capacitor mounting holes:1
- Chassis Dimensions(without mounting flange): 17" x 6-½" x 2-½"
Chassis Measurements:
- Power transformer mounting centers: 3-7/16” x 2-3/4”
- Output transformer mounting centers: 2-1/2” x 2-3/8”
- Choke mounting centers: (#1) 2-7/8” (#2) 3-3/16”
- Can cap mounting centers : 2”
- Octal (8-pin) tube sockets: 1-1/2”
- Noval (9-pin) tube sockets: 1-1/8”
Compatible Part Links:
- Noval socket with shield base: P-ST9-700
- Noval socket (no shield): P-ST9-600
- Octal socket : P-ST8-600
- Output transformer: P-T1750Q
- Choke: P-C194G
$88.47

Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box.
$9.95

Colors Available:
New!:
Starting at $4.95

Colors Available:
New!:
Starting at $5.95

Same as Hammond P-H1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ ½" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.
$9.95

Colors Available:
Starting at $8.95

Diecast Aluminum Chassis Box, 7.4” x 4.7” x 1.3”. Six included machine screws secure lid.
$13.50

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
- Add 0.16" to enclosure depth for lid.
$7.95

Colors Available:
New!:
Measures 4.77" x 2.60" x 1.39".
Starting at $6.59

Colors Available:
- Slightly beveled top and rounded corners for high quality look.
- Tight fit and small gap between the enclosure and lid.
- Undercut boss allows more internal room for more flexible layout.
- Smooth, eggshell-like matte powder coating.
- Recessed bottom lid
$14.95

Colors Available:
- Beveled top and rounded corners for high quality look.
- Tight fit and small gap between the enclosure and lid.
- Undercut boss allows more internal room for more flexible layout.
- Smooth, eggshell-like matte powder coating.
$14.95

Special Order Item
Hammond natural aluminum chassis box. Measures 17" x 13" x 2".
$39.97

Special Order Item
Hammond aluminum chassis box with walnut sides. Measures 12" by 8" by 3".
$85.36

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$6.22

Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $7.07

The Hammond 1590B2 is a version of the ubiquitous 1590B with a little more vertical space. Great for any designs that require more clearance and allows for easier top-mounted jacks.
$7.73

- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
- Add 0.16" to enclosure depth for lid.
$8.90

Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $9.42