The Mod® Electronics Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction. This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours. All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.

The Mod® Electronics Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.

The Mod® Electronics Persuader Deluxe utilizes a Darlington preamp to push cascaded triode vacuum tubes into distortion. A boost switch provides an additional layer of flexibility with added gain and a little extra bottom end. An LED indicator lights up when the Persuader Deluxe is engaged and not in true bypass mode. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.

The Mod® Electronics Piledriver is a clean-boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!

The Mod® Electronics Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.

The Mod® Electronics Penetrator is a treble boost pedal kit with enough gain to cut straight through any mix. This pedal adds glistening harmonics that get loud enough to saturate your amp’s front end. Adjust the level knob to vary the output so there’s no mistaking when you kick this pedal in. Great for solos or when you need your guitar front and center.

A T-Filter Pedal Kit - the Mod® Electronics Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.

The Seismic / Shift is a JFET boost based on one of the earliest effects to ever be used on stage. This pedal adds subtle color to a guitar's sound while maintaining the natural tone of the guitar. It packs a serious punch that can cut through any mix when soloing or whenever some extra “umph” is required. The Seismic Shift pairs nicely with amps and other pedals. Place it ahead of tubes, preamps, overdrives, distortions, and fuzz pedals to shift your gear onto a new level. The Seismic Shift pedal kit is the introduction to the Nexus Series from Mod Electronics. This series features a PCB base rather than the Mod Electronics’ traditional point-to-point wiring kits to offer builders an even wider variety of effects to build. The Seismic Shift kit is designed for all skill sets and is the perfect first build for those unfamiliar with PCB construction. The pedal operates on both 9VDC and 18VDC.

The Mod® Electronics Rock Bottom is a bass fuzz kit that gives you all of the sizzle you'd expect from a vintage fuzz without sacrificing those low frequencies. Use the blend pot to set your fuzz levels and dial in the volume to get that sound you need. This versatile pedal can be used for the sludgiest bass tones to the cleanest boost and everything in-between.

The Mod® Electronics Verb Deluxe kit is built around the Belton Digi-Log Mini Module (P-RBTDR-2H-X) for a great digital reverb sound. The Belton Digi-Log module was built as a replacement for traditional spring reverberation units. Features include both Dwell and Mix controls, allowing the dry signal to be blended with the processed signal from a just hint of reverb to deep, cavernous echoes. The dwell control adds an extra flexibility, providing a full palette of sweet reverb sound. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.

The Mod® Electronics MOD 102 is a great place to start for those interested in building their own tube amp. It is based on a classic American tube-circuit design combined with a British style Class A output tube section. At low volume it produces a clean chimey tone that moves into smooth overdrive at higher volumes. All parts are included along with a pre-drilled steel chassis, wire and tubes (1 EL84 and 1 12AX7). Puts out at least 5 watts. The chassis layout is open for easy assembly using the clear, easy to follow instructions.

The Mod® Electronics MOD102+ expands on the same all analog vacuum tube classic American circuit design combined with a British style Class A output section as the Original MOD102 with added additional “+” features. These special features include a three position progressive toggle switch for off-standby-power and additional push-pull functionality for each control - pull out the bass control knob for “mid boost”, pull out the treble control knob for “bright”, pull out the volume control knob for “turbo”.

The Maxon OD808 is an identical circuit to the original TS808 Tubescreamer Maxon designed and built in the late 1970s. Featuring a JRC4558, the OD808 offers the same natural overdriven tones as the original pedals used widely across all genres of music. The OD808 has a warmer and smoother tone than the OD-9 that pairs nicely with clean amps in addition to sounding great in just about any rig.
Features

• Natural and smooth overdrive effects with tube-like saturation
• Preserves the original tone of the instrument
• Produces a variety of sound ranging from a clean boost to fully saturated overdrive
• LED indicator for effect on/off
• DC power or 9V battery
• Made in Japan

The RAT2 is the classic distortion pedal in the Pro Co RAT family. It has a unique tone structure that other effect devices are measured against. The beauty of the RAT 2 lies in its versatility. Used as a primary distortion, it excels at arena rock rhythm tones and soaring leads.