You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

 

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(14 pages)
P-H16-150Bumper - Morley, tapered rubber feet, self adhesive (Package of 20)

Small tapered rubber feet with self-adhesive backing (package of 20). Can be used to provide grip and slight elevation (about 0.14") when secured to most project enclosures. Great for effects pedals and rack mount units when removed from the rack.


$5.00
Click to read more
P-H511Switch - Replacement for Boss Effects Pedals
Replacement for Boss effects pedals, SPST momentary, push switch. Mounts in square hole approximately.55" x.55" x 1.08" overall length including terminals.
$2.50
Click to read more
P-ECB-24BPotentiometer - Dunlop, Hot Potz II Crybaby, 100K
Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100K ohm. Original Dunlop replacement part.
The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.
$19.95
Click to read more
K-950Effects Pedal Kit - MOD® Kits, The Thunderdrive, Overdrive
The Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction.
This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours.
All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.
$29.95
Click to read more
K-920Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost

"The PileDriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!


$24.95
Click to read more
K-955Effects Pedal Kit - MOD® Kits, Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe is an overdrive pedal kit that will provide a strong clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting volume control and gain controls provides a wide variety of tones in spite of it's simple contruction.
The Turbo switch provides an additional boost in volume and less internally generated distortion. The pre-painted black enclosure, red control knobs and red LED indicator give the Thunderdrive Deluxe an understated attractive finish. It is capable of overdriving the preamp section of your guitar amp or adding it's own layer of distortion at lower volume.
This is an easy build kit with point to point wiring and clear, easy to follow instructions. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life. All you need to provide is solder, soldering iron and a few simple tools.
$39.95
Click to read more
P-H501Switch - Footswitch, 3PDT, Blue, high quality

Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. High quality, made in Taiwan.


$6.95
Click to read more
K-930Effects Pedal Kit - MOD® Kits, The Persuader, Tube Drive
Build your own tube preamp pedal built around a 12AX7 tube. Go from clean, warm tone to smooth, real tube overdrive.
This kit includes pre-drilled die-cast aluminum enclosure and all parts with easy to follow instructions. All you need to provide is solder and soldering iron.
The Persuader allows for easy access to the tube, giving you the ability to quickly experiment with different tube brands and 12AX7 tube relatives.
Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$64.95
Click to read more
P-H497Switch - Carling, Footswitch, DPDT, On-On, Side Solder Lugs
Good stomp-box effects switch (Double Pole, Double Throw), On-On. Solder Lugs. 1A 250V, 3A 125V

Note: On-On switches may sometimes be referred to as On-None-On.
$7.95
Click to read more
P-H492Switch - Carling, Footswitch, SPDT

Carling SPDT footswitch used in footswitch boxes and effects pedals (112-P).


$6.95
Click to read more

Pages

(14 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts