Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects. Build a kit or purchase parts to make your own!
M-PAS-CABLE-1 Cable - Power All, 5 Lead Right Angle Daisy Chain
Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the PA-9 Power-All to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices
$7.50
R-VPC01 Photo Cell - Morley, for Effects Pedals
Photocell for Morley effects pedals. Great replacement for LDR1, LDR2 and LDR3 (M79-211564-000) in Morley Pro Series Volume PVO. Sold individually.
$2.50
P-H1590BBCE-PD Chassis Box - Aluminum, 4.67" x 3.68" x 1.18", pre-drilled
Same as Hammond P-H1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ ½" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.
$9.95
P-ECB-126 Gear - Dunlop, replacement for Wah
Original Dunlop replacement gear for wah potentiometers (C-ring included). The gear has 14 teeth and a flatted inner diameter to fit securely onto a potentiometer with flatted shaft. The included C-ring is placed over the top end of the gear to keep it from sliding off the end of the potentiometer shaft.
$1.95
P-H503-PC Switch - Footswitch, DPDT, Momentary, PC Terminals
DPDT momentary footswitch with PC terminals. Black with 6 terminals. AC125V 4A, AC250V 2A.
$4.50
R-VWAH-LP Potentiometer - 100kΩ, Wah Replacement, Life, Smooth
100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrade is sold with all necessary hardware and gear for immediate installation.
$11.95
M-PAS-CABLE-7 Cable - Power All, Red Right Angle Reverse Polarity Jumper
Included in the Power-All System and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.
$3.00
P-H1590X Chassis Box - Hammond, Unpainted Aluminum, 5.7" x 4.8" x 2.1"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$12.91
Save 10%
Originally: $14.34
P-H551 Switch - Carling, Footswitch, SPST, Off-(On), Screw Terminals
Carling, SPST footswitch, Off-(On), momentary, normally open with screw terminals. Note: Off-(On) switches may sometimes be referred to as Off-None-(On).
$4.06
Save 42%
Originally: $6.95
K-977 Effects Pedal Kit - MOD® Kits, Suspended Chime, Chorus, Delay
The Suspended Chime has two powerful effects in one pedal - chorus and chorus/delay. The Suspended Chime features a blend knob which allows you to go from subtle to lush chorus effect in either set up. Using the selector switch, you can add a 190 millisecond delay to the chorus introducing special depth to your tone. Varying the dry/wet mix can fatten your rhythms or produce a shimmering 12-string sound. The Suspended Chime kit comes equipped with an LED indicator and industry standard 9 volt center negative power jack. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. All effects pedals operate on a 9V battery.
$99.95
P-ECB-555 Switch - Dunlop, Footswitch, DPDT, Solder Lugs, for MXR
Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR, Cry Baby, and other effects pedals.
$14.95
P-H1590N1 Chassis Box - Hammond, Unpainted Aluminum, 4.77" x 2.6" x 1.39"
Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
$9.73
Save 10%
Originally: $10.81
M-PAS-CABLE-3 Cable - Power All, Black Right Angle Extension Jumper
Included in the Power-All System and also sold separately, the Cable-Black/R allows the user to power over-sized effect units or units w/AC jacks in hard-to-reach places off of the Power-All Daisy Chain. The Cable-Black can be connected to any plug on any Power-All daisy chain, or directly to the PA-9 itself.
$3.00
P-ECB-004 Power Supply - Dunlop, 18V A/C Adapter
The Dunlop 18V power supply for Dunlop effects will save you some money on batteries and get the right power to your pedal! Features Include:
  • 18 volts of regulated DC current
  • 2.1 mm x 5.5 mm plug with negative center

Compatible Dunlop pedals include:
  • Older Crybaby Multi-Wah
  • SW-95 Slash Wah
  • M108 10-band EQ
  • KFK1 10-band EQ
  • M117R Flanger
  • EVH 117 Flanger
  • DD11 Dime Distortion
  • M134 Chorus
  • M181 Bass Blowtorch

Plus many other pedals requiring an 18vdc power supply!
$15.95
P-ECB-003 Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative

Dunlop ECB003 US wallwart power supply. Barrel connector.

  • Voltage: 9VDC
  • Current: 200mA
  • Tip Negative; Sleeve positive
$12.50
P-H1590E Chassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$19.52
Save 10%
Originally: $21.69
P-ECB-HI01 Inductor - Dunlop, for Crybaby, HI01 Halo Inductor
Cry Baby Genuine Replacement Part HI01 Halo Inductor. Used in the famous Clyde McCoy® wah, the Halo Inductor is the key to late ’60s American wah tone. The HI01 delivers that vintage sound, with its expressive sweep and throaty voice, while minimizing microphonic noise due to its stabilized cup-core material.
$45.95
K-995 Effects Pedal Kit - MOD® Kits, The Aggressor, Distortion
The Aggressor is a high-gain distortion pedal kit that delivers contemporary distortion with plenty of chunk and ear-splitting pitch harmonics. The distortion effect goes from subtle break-up to over-the-top molten distortion at maximum gain.
The Aggressor features true bypass, LED indicator, and a versatile tone control with a scoop/bump switch that shifts the mid-frequency response, allowing you to craft a tone that fits your style of playing. It works well with humbuckers and single-coil pickups, so you can turn any guitar into a lethal weapon capable of inflicting serious brain damage and spontaneous combustion!
MOD® Kits are designed to give novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy-to-follow instructions and use point-to-point wiring. A pre-drilled enclosure and all necessary parts are included.
$74.95
K-998 Effects Pedal Kit - MOD® Kits, Tone Attack, Active Tone Stack
Shape your sound with the Tone Attack. 12 o'clock settings give an approximate unity gain with the pedal. Rotate the treble or bass knob counterclockwise to cut the corresponding frequencies. Rotate these same knobs clockwise to boost the frequency bands. The master boost knob can be used to attenuate your signal or push your tone to screaming loud volumes. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. The Tone Attack operates on a 9V battery or AC adapter, which is not included. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$64.95
P-ECB-002 Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
  • Voltage: 9VDC
  • Current: 200mA
  • Tip positive; Sleeve negative
$12.50
M-PAS-CABLE-5 Cable - Power All, Green Right Angle Line-6 Extension Jumper
Included in the Power-All system and also sold separately, the Cable-Green Right Angle jumper allows the user to power Line-6 Stomp-Box modelers and other digital effect units from the PA-9. The Cable-Green features a reverse-polarity (tip positive), right-angle male barrel connector with a larger, 2.5 mm internal diameter and spring-loaded clips.
$3.00
P-ECB-233 Switch - Dunlop, PCB mount, boost / distortion kick switch
ECB233 boost / distortion kick switch. Original Dunlop replacement part. Used in the SW95 Crybaby Slash Wah. Through hole PCB mount.
$4.50
M-OD808 Effects Pedal - Maxon, OD808, Overdrive
The Original Overdrive! The OD808 is often imitated but never matched! Identical to the 1970s circuit and featuring the JRC4558 IC chip, it offers warm, smooth, transparent overdrive that'll make your rig scream! The OD808's dynamically responsive circuitry reacts precisely to individual playing styles, letting the true voice of any instrument or artist shine through. Don't settle for copies when you can have the original. The OD808 Reissue offers up all the warm, creamy, organic overdrive as the original and then some. Never one to rest on their laurels, Maxon has tweaked the current version ever so slightly to reduce noise level while retaining the legendary “808" tone. The OD808 is the perfect pedal for adding smooth, tube-like overdrive to any clean amp – use it as a secondary dirt channel to beef up a song's chorus section, or keep it on all the time for the crunchy tone that has defined rock and roll.
$149.00
P-ECB-24C Potentiometer - Dunlop, 20 kΩ, Custom Taper, Wah Pot, for Bass
Custom taper 20k Dunlop potentiometer used in 105Q Crybaby Bass Wah. 1 million cycles, maintenance free.
$22.95
Don't see what you're looking for? Send us your product suggestions!