Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects. Build a kit or purchase parts to make your own!
K-991 Effects Pedal Kit - MOD® Kits, The Rock Bottom, Bass Fuzz
The Rock Bottom is a bass fuzz kit that gives you all of the sizzle you'd expect from a vintage fuzz without sacrificing those low frequencies. Use the blend pot to set your fuzz levels and dial in the volume to get that sound you need. This versatile pedal can be used for the sludgiest bass tones to the cleanest boost and everything in-between.
$43.95
P-ECB-25 PC Board - Dunlop, for Crybaby
Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
$22.95
P-ECB-FI-01 Inductor - Dunlop, Fasel, Toroidal with Cup Core Tone, Yellow
This yellow fasel is a Toroidal design with the tonal character of a cup core, best for attaining a vintage vibe. Use the precision-wound Toroidal, part number P-ECB-FI-02, for the cleanest sound possible. The Fasel inductor is back! These near-mythical inductors are the key to the singing tonal sweep every wah player lusts for but can't capture with a new pedal. The ultimate upgrade to your current wah, these magic bullets are available exclusively from Dunlop, the new worldwide agent for Fasel of Italy. Your wah will finally give up the lush harmonic sparkle you've always heard in your head but could never coax from your rig.
$15.95
M-PAS-X Power Supply - Power All System, For Effects Pedals
The Power-All PA-9 Digital Power Supply is the world’s first 2,000 mA, single outlet power supply designed specifically for guitar effect users. Don’t waste money on batteries or take up valuable space with multiple “wall wart” adaptors or power bricks – the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All provides 9 volts DC at 2,000 milliamps – more than enough current to power dozens of effect pedals, including up to four Line 6 Modelers! The Power-All’s special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9 now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.
Starting at $24.95
P-ECB-131 Knob Cover - Dunlop, for MXR knobs
Replacement black rubber knob cover for Original MXR knob (P-ECB-130). Original Dunlop replacement part.
$1.75
P-H410-A Footswitch - 4PDT, Black, Solder Lugs
Quad Pole, Double Throw (4PDT), latching footswitch with 12 solder lugs.
$4.95
P-H1590CX Chassis Box - Hammond, Diecast Aluminum, 4.72" x 3.70" x 2.10"
Colors Available:
New!:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $11.32
P-ECB-40 ¼" Jack - Dunlop, Stereo, for effects pedals
Stereo jack for Dunlop effects pedals. Original Dunlop replacement part. Though hole PCB mount with six pins.
$3.35
P-H1590BBCE-X Chassis Box - Diecast Aluminum, 4.67" x 3.68" x 1.18"
Colors Available:
Chassis box perfectly suited for effects pedals and other DIY projects.
Starting at $8.95
P-ECB-24A Potentiometer - Dunlop Hot Potz, 470 kΩ
Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.
$22.95
P-H1590XX Chassis Box - Hammond, Diecast Aluminum, 5.3" x 4.4" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$13.02
P-ECB-126 Gear - Dunlop, replacement for Wah
Original Dunlop replacement gear for wah potentiometers (C-ring included). The gear has 14 teeth and a flatted inner diameter to fit securely onto a potentiometer with flatted shaft. The included C-ring is placed over the top end of the gear to keep it from sliding off the end of the potentiometer shaft.
$1.95
M-PAS-CABLE-1 Cable - Power All, 5 Lead Right Angle Daisy Chain
Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the PA-9 Power-All to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices
$7.50
K-999 Effects Pedal Kit - MOD® Kits, The Saturator
The Saturator is an overdrive pedal kit that can cover a wide range of gain effects, transitioning smoothly from a massive clean boost to a warm and saturated distortion with the turn of a knob. The saturation is controlled with the "Soak" knob, which dials in the amount of symmetrical soft-clipping applied to the guitar signal. When fully counterclockwise , the signal is unaffected and clean. Rotating the knob clockwise will incrementally increase the soft-clipping, morphing from a clean signal through subtle-to-heavy saturated overdrive sounds and straight into distortion territory. The "Level" knob sets the overall volume of the clean or saturated output. Unity gain is at roughly 8 o'clock. With the "Soak" set to clean, rotating the "Level" knob clockwise will increase the level to upwards of 30dB.
$47.95
P-H1590BBX Chassis Box - Hammond, Diecast Aluminum, 4.67" x 3.68" x 1.18"
Colors Available:
New!:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $9.42
P-H1590D Chassis Box - Hammond, Diecast Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$19.34
P-RBTDR-2V-X Reverb Module - Accutronics, Digi-Log, vertical mount, mini
A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface requires only input, output, +5V, and ground.
$14.95
P-H503-PC Footswitch - DPDT, Momentary, PC Terminals
DPDT momentary footswitch with PC terminals. Black with 6 terminals. AC125V 4A, AC250V 2A.
$4.50
P-ECB-9V1A Battery Box - Gotoh, single, 9 volt
Single 9 volt battery box. See P-ECB-9V1B for single battery box with removable adapter. See P-ECB-9V2 for double battery box.
$13.95
K-977 Effects Pedal Kit - MOD® Kits, Suspended Chime, Chorus, Delay
The Suspended Chime has two powerful effects in one pedal - chorus and chorus/delay. The Suspended Chime features a blend knob which allows you to go from subtle to lush chorus effect in either set up. Using the selector switch, you can add a 190 millisecond delay to the chorus introducing special depth to your tone. Varying the dry/wet mix can fatten your rhythms or produce a shimmering 12-string sound. The Suspended Chime kit comes equipped with an LED indicator and industry standard 9 volt center negative power jack. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. All effects pedals operate on a 9V battery.
$99.95
P-ECB-152 Bottom Plate - Dunlop, for GCB-95 with Battery Door
Bottom Plate for GCB-95. Original Dunlop replacement part. Includes battery box, four mounting screws and four black rubber feet.
$13.95
P-ECB-9V2 Battery Box - Gotoh, Dual, 9 Volt
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.00
P-H1590BBCE-PD Chassis Box - Diecast Aluminum, 4.67" x 3.68" x 1.18", pre-drilled
Same as Hammond P-H1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ ½" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.
$9.95
P-H503 Footswitch - DPDT, Momentary, Solder Lugs
DPDT momentary footswitch. AC125V/4A AC250V/2A
$3.95
Don't see what you're looking for? Send us your product suggestions!