Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects. Build a kit or purchase parts to make your own!
P-L600-X LED - 3mm, Water Clear, High Brightness, Package of 5
Package of 5
Colors Available:
High brightness 3mm LED. Great for use in pedal builds and other applications where a bold, bright, indicator is needed. Multiple colors available.
  • 3mm size
  • Water clear
  • High brightness
  • Multiple colors available
  • Package of 5
Starting at $1.30
P-L700-X LED - 5mm, Water Clear, High Brightness, Package of 5
Package of 5
Colors Available:
High brightness 5mm LED. Great for use in pedal and amp builds as well as other applications where a bold, bright, indicator is needed. Multiple colors available.
  • 5mm size
  • Water clear
  • High brightness
  • Multiple colors available
  • Package of 5
Starting at $1.30
P-L300X LED - 3mm diameter, diffused lens
Package of 5
Colors Available:
Lens Diameter: 3 mm Overall Height: 5.4 mm Lens Type: Diffused Multiple color options available.
$0.65
P-LRING-X LED - Footswitch Ring, With Bezel, 9V
Colors Available:
Leaded LED rings for use with standard footswitches. These LED rings use an array of LEDs with internal current limiting so no additional parts are required for use with 9VDC. Red, green, blue, and two-color combinations are available. A 15mm panel hole is required. See full dimensions below to check footswitch compatibility.
Starting at $1.50
P-H511 Switch - Replacement for Boss Effects Pedals
Replacement for Boss effects pedals, SPST momentary, push switch. Mounts in square hole approximately. 55" x.55" x 1.08" overall length including terminals.
$2.50
P-ECB-151 Rubber feet - Dunlop, for Crybaby, includes screws
Package of 4
Rubber feet with screws for Dunlop Crybaby Wah pedal. Package of four. Original Dunlop replacement part. Rubber foot diameter: 5/8" Rubber foot height: 5/16" Screw threading: #6-32 (screw extends 5/16" beyond the rubber surface)
$2.60
P-H1590BX Chassis Box - Hammond, Diecast Aluminum, 4.40" x 2.38" x 1.06"
Colors Available:
New!:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $7.07
P-H493 Footswitch - Carling, SPST, for Fender® Switching Pedals
Carling SPST footswitch. Used in Fender etc. Reverb/tremolo/channel switching pedals, (110-P).
$5.95
P-RBTDR-3H Reverb Module - Accutronics Belton, Digi-Log, Adjustable Decay
A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface: input, output, +5V, and ground
$15.95
P-L500 LED Bezel - with included 5mm Red LED
5 mm diameter Red LED with holder. Perfect for amps and effects. Mounts in a 5/16" diameter chassis hole.
$1.05
P-H590-X Footswitch - 3PDT, with built-in LED Ring
Colors Available:
3PDT. LED ring requires a 11/16" mounting hole. Foot switch button set screw requires 1.5mm hex key.
$8.25
P-H492 Footswitch - Carling, SPDT
Carling SPDT footswitch used in footswitch boxes and effects pedals (112-P).
$6.95
P-RBTDR-2H-X Reverb Module - Accutronics Belton, Digi-Log, horizontal, mini
A great digital reverb sound that easily replaces a spring reverberation unit. Small package is half the size of the P-RBTDR-1H-X
$14.95
P-H604 Footswitch - SPST, Momentary, Solder Lugs, Soft Switch
SPST(single pole,single throw) normally open, Off-(On) momentary foot switch. Solder lugs, soft switching. These high quality switches are great for upgrading the footswitch in relay based pedals as well as tap tempo applications. Depressing the switch shorts the lugs together and when the switch is released it returns to it’s non connected state with no click.
  • SPST momentary switch
  • Soft, silent switching with no click
  • Normally open operation
  • Solder lugs
  • Nuts and washer included

Note: Off-(On) switches may sometimes be referred to as Off-None-(On).
$2.85
S-H750-X Power Jack - DC Panel Mount, 5.5mm External, 2.1mm Internal
Colors Available:
½" panel mount with solder lugs. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
$0.95
P-L200 LED Bezel - for mounting 3mm LEDs
Holder for mounting LEDs to panels.
$0.65
P-H552X Footswitch - Carling, SPST, Momentary, Solder Lugs
Carling, SPST footswitch, momentary with solder lugs. Provides a compact yet rugged solution to general purpose switch needs. Alternate action, metal construction and stiff (6-8 lb) actuation force have combined to make this switch a pillar in a variety of markets.
$7.95
P-ECB-24B Potentiometer - Dunlop, Hot Potz II Crybaby, 100 kΩ
Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100 kΩ. Original Dunlop replacement part. The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.
$20.59
P-H1590N1CE Chassis Box - Diecast Aluminum, 4.77" x 2.60" x 1.39"
Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Measures 4.77" x 2.60" x 1.39".
$6.59
P-ECB-244 Battery Box - Dunlop, snap-in enclosure
Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.
$1.95
P-ECB-130 Knob - Dunlop, MXR Knob for pedals, skirted
Large MXR knob with set screw for MXR pedals. Original Dunlop replacement part. Skirted knob with white line and dot indicator.
$3.45
P-ECB-124 Grommets - Dunlop, Offset, 3x4 Different Sizes
Package of 12
Original Dunlop offset grommets (i.e. rubber bumpers) used on the underside of the treadle piece (rocking structure) of wah pedal enclosures. Made in USA.
$6.95
P-H550 Footswitch - DPDT, Bottom Solder Lugs
Carling, DPDT footswitch, On-On, with solder lugs. Provides a compact yet rugged solution to general purpose switch needs. Alternate action, metal construction and stiff (6-8 lb) actuation force have combined to make this switch a pillar in a variety of markets.
$10.95
P-H1590A Chassis Box - Hammond, Diecast Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$6.22
Don't see what you're looking for? Send us your product suggestions!