Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects. Build a kit or purchase parts to make your own!

Mod Kits

Mod® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring.

Hammond

Hammond Manufacturing offers a full range of transformers, chokes and enclosures.
K-950 Effects Pedal Kit - MOD® Kits, The Thunderdrive, Overdrive
The Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction. This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours. All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.
$29.95
K-920 Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost
"The Piledriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!
$27.95
K-955 Effects Pedal Kit - MOD® Kits, The Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe is an overdrive pedal kit that will provide a strong clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting volume control and gain controls provides a wide variety of tones in spite of it's simple contruction. The Turbo switch provides an additional boost in volume and less internally generated distortion. The pre-painted black enclosure, red control knobs and red LED indicator give the Thunderdrive Deluxe an understated attractive finish. It is capable of overdriving the preamp section of your guitar amp or adding it's own layer of distortion at lower volume. This is an easy build kit with point to point wiring and clear, easy to follow instructions. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life. All you need to provide is solder, soldering iron and a few simple tools.
$39.95
K-970 Effects Pedal Kit - MOD® Kits, The Tea Philter, T Filter
The Tea Philter - A T-Filter Pedal Kit The Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.
$31.95
K-930 Effects Pedal Kit - MOD® Kits, The Persuader, Tube Drive
Build your own tube preamp pedal built around a 12AX7 tube. Go from clean, warm tone to smooth, real tube overdrive. This kit includes pre-drilled die-cast aluminum enclosure and all parts with easy to follow instructions. All you need to provide is solder and soldering iron. The Persuader allows for easy access to the tube, giving you the ability to quickly experiment with different tube brands and 12AX7 tube relatives. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$67.95
K-980 Effects Pedal Kit - MOD® Kits, The Persuader Deluxe, Overdrive
The Persuader Deluxe utilizes a Darlington preamp to push cascaded triode vacuum tubes into distortion. Four dual triode vacuum tubes are included with each kit (JJ 5751, 12AX7B China, JJ 12AU7 and a NOS USA-made 12AT7). Swap to create a wide range of tones from just a hint of break up from the JJ 5751 to over the top crunchy distortion using the NOS US made 12AT7. A boost switch provides an additional layer of flexibility with added gain and a little extra bottom end. An LED indicator lights up when the Persuader Deluxe is engaged and not in true bypass mode. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$99.95
K-960 Effects Pedal Kit - MOD® Kits, The Trill Tremolo
The Trill Tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.
$46.95
K-965 Effects Pedal Kit - MOD® Kits, The Contortionist II, Fuzz
The Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.
$47.95
K-915 Effects Pedal Kit - MOD® Kits, The Verb Deluxe, Digital Reverb
The Verb Deluxe kit is built around the Belton Digi-Log Mini Module (P-RBTDR-2H-X) for a great digital reverb sound. The Belton Digi-Log module was built as a replacement for traditional spring reverberation units. Features include both Dwell and Mix controls, allowing the dry signal to be blended with the processed signal from a just hint of reverb to deep, cavernous echoes. The dwell control adds an extra flexibility, providing a full palette of sweet reverb sound. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$79.95
K-985 Effects Pedal Kit - MOD® Kits, The Wahtz, Wah
The Wahtz Wah Pedal Kit produces the classic Wah tone you've come expect with a hint of extra bite and growl.
True bypass switching insures no loss of signal when the Wah effect is not engaged; and the long life potentiometer manufactured specifically for use in Wah pedals is included to provide years of smooth, quiet operation.
Point to point construction allows advanced kit builders to easily experiment with modifications to further tailor the tone to more individual tastes.
MOD® Kits and Assemblies are designed to give novice and experienced musicians the opportunity to build or modify their own amps, effects pedals and guitars. All kits come with easy-to-follow instructions and use point-to-point wiring. All effect pedals and amplifiers come with a pre-drilled enclosure and all necessary parts are included. All you need to provide are hand tools, a soldering iron and solder.
$109.95
K-978 Effects Pedal Kit - MOD® Kits, The Step Ladder, Input Attenuator
The Step Ladder is a passive input attenuator using high quality components for excellent reliability. True-bypass mode provides the maximum signal level. The attenuator pot and two toggle switches allow for flexibility in the amount of signal attenuation when not in bypass mode. Treble bleed capacitors in the circuit retain crisp high frequencies even at maximum attenuation. The Step Ladder is ideal for anything from getting a slight boost while playing single-note acoustic guitar leads or for jumping from clean to overdrive in a high-gain electric guitar amp.
$36.95
P-H1590BX Chassis Box - Hammond, Diecast Aluminum, 4.37" x 2.37" x 1.22"
Colors Available:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $7.07
P-H1590LB Chassis Box - Hammond, Unpainted Aluminum, 1.99" x 1.99" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$6.14
K-995 Effects Pedal Kit - MOD® Kits, The Aggressor, Distortion
The Aggressor is a high gain distortion pedal kit that delivers contemporary distortion with plenty of chunk and ear-splitting pitch harmonics. The distortion effect goes from subtle break-up to over-the-top molten distortion at maximum gain. The Aggressor features true bypass, LED indicator, and a versatile tone control with a scoop/bump switch that shifts the mid-frequency response allowing you to craft a tone that fits your style of playing. It works well with humbuckers and single coil pickups, so you can turn any guitar into a lethal weapon capable of inflicting serious brain damage and spontaneous combustion! MOD® Kits are designed to give novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy-to-follow instructions and use point-to-point wiring. A pre-drilled enclosure and all necessary parts are included.
$74.95
K-991 Effects Pedal Kit - MOD® Kits, The Rock Bottom, Bass Fuzz
The Rock Bottom is a bass fuzz kit that gives you all of the sizzle you'd expect from a vintage fuzz without sacrificing those low frequencies. Use the blend pot to set your fuzz levels and dial in the volume to get that sound you need. This versatile pedal can be used for the sludgiest bass tones to the cleanest boost and everything in-between.
$43.95
K-996 Effects Pedal Kit - MOD® Kits, The Penetrator, Treble Boost
The Penetrator is a treble boost pedal kit with enough gain to cut straight through any mix. This pedal adds glistening harmonics that get loud enough to saturate your amp’s front end. Adjust the level knob to vary the output so there’s no mistaking when you kick this pedal in. Great for solos or when you need your guitar front and center.
$38.95
P-H1590D Chassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$19.34
P-H1590A Chassis Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$6.22
P-H1590C Chassis Box - Hammond, Unpainted Aluminum, 4.72" x 3.70" x 2.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$11.32
P-H1590BBX Chassis Box - Hammond, Aluminum, 4.67" x 3.68" x 1.18"
Colors Available:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $9.42
P-H1590XX Chassis Box - Hammond, Unpainted Aluminum, 5.3" x 4.4" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$13.02
P-H1590X Chassis Box - Hammond, Unpainted Aluminum, 5.3" x 4.4" x 2.2"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$14.34
P-H1590E Chassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$21.69
P-H1590F Chassis Box - Hammond, Unpainted Aluminum, 7.38" x 7.38" x 2.48"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$27.31
Don't see what you're looking for? Send us your product suggestions!