Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects. Build a kit or purchase parts to make your own!
P-H16-150 Bumper - Morley, tapered rubber feet, self adhesive
Package of 20
Small tapered rubber feet with self-adhesive backing (package of 20). Can be used to provide grip and slight elevation (about 0.14") when secured to most project enclosures. Great for effects pedals and rack mount units when removed from the rack.
$5.00
P-H511 Switch - Replacement for Boss Effects Pedals
Replacement for Boss effects pedals, SPST momentary, push switch. Mounts in square hole approximately. 55" x.55" x 1.08" overall length including terminals.
$2.50
P-ECB-24B Potentiometer - Dunlop, Hot Potz II Crybaby, 100K
Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100K ohm. Original Dunlop replacement part. The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.
$20.59
K-950 Effects Pedal Kit - MOD® Kits, The Thunderdrive, Overdrive
The Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction. This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours. All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.
$29.95
K-920 Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost
"The PileDriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!
$24.95
K-955 Effects Pedal Kit - MOD® Kits, Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe is an overdrive pedal kit that will provide a strong clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting volume control and gain controls provides a wide variety of tones in spite of it's simple contruction. The Turbo switch provides an additional boost in volume and less internally generated distortion. The pre-painted black enclosure, red control knobs and red LED indicator give the Thunderdrive Deluxe an understated attractive finish. It is capable of overdriving the preamp section of your guitar amp or adding it's own layer of distortion at lower volume. This is an easy build kit with point to point wiring and clear, easy to follow instructions. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life. All you need to provide is solder, soldering iron and a few simple tools.
$39.95
P-H501 Switch - Footswitch, 3PDT, Blue, Taiwan
Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in Taiwan.
$6.95
P-H492 Switch - Carling, Footswitch, SPDT
Carling SPDT footswitch used in footswitch boxes and effects pedals (112-P).
$6.95
K-970 Effects Pedal Kit - MOD® Kits, The Tea Philter, T Filter
The Tea Philter - A T-Filter Pedal Kit The Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.
$31.95
K-930 Effects Pedal Kit - MOD® Kits, The Persuader, Tube Drive
Build your own tube preamp pedal built around a 12AX7 tube. Go from clean, warm tone to smooth, real tube overdrive. This kit includes pre-drilled die-cast aluminum enclosure and all parts with easy to follow instructions. All you need to provide is solder and soldering iron. The Persuader allows for easy access to the tube, giving you the ability to quickly experiment with different tube brands and 12AX7 tube relatives. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$64.95
P-H493 Switch - Carling, Footswitch, SPST, for Fender® & Others
Carling SPST footswitch. Used in Fender etc. Reverb/tremolo/channel switching pedals, (110-P).
$5.95
P-H497 Switch - Carling, Footswitch, DPDT, On-On, Side Solder Lugs
Good stomp-box effects switch (Double Pole, Double Throw), On-On. Solder Lugs. 1A 250V, 3A 125V
Note: On-On switches may sometimes be referred to as On-None-On.
$7.95
K-980 Effects Pedal Kit - MOD® Kits, The Persuader Deluxe, Overdrive
The Persuader Deluxe utilizes a Darlington preamp to push cascaded triode vacuum tubes into distortion. Four dual triode vacuum tubes are included with each kit (JJ 5751, 12AX7B China, JJ 12AU7 and a NOS USA-made 12AT7). Swap to create a wide range of tones from just a hint of break up from the JJ 5751 to over the top crunchy distortion using the NOS US made 12AT7. A boost switch provides an additional layer of flexibility with added gain and a little extra bottom end. An LED indicator lights up when the Persuader Deluxe is engaged and not in true bypass mode. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$99.95
S-H155 Battery Clip - 9 Volt
Package of 3
9 volt battery clip with 5 3/4" red and black wire lengths. Simple construction and perfect for use in effects pedals. Package of three.
$0.60
S-H750-X Power Jack - DC Panel Mount
Colors Available:
½" panel mount with solder lugs. Round plastic with normally closed switch.
$0.95
P-RBTDR-2H-X Reverb Module - Accutronics Belton, Digi-Log, horizontal, mini
A great digital reverb sound that easily replaces a spring reverberation unit. Small package is half the size of the P-RBTDR-1H-X
$14.95
P-ECB-151 Rubber feet - Dunlop, for Crybaby, includes screws
Package of 4
Rubber feet with screws for Dunlop Crybaby Wah pedal. Package of four. Original Dunlop replacement part. Rubber foot diameter: 5/8" Rubber foot height: 5/16" Screw threading: #6-32 (screw extends 5/16" beyond the rubber surface)
$2.60
P-H498 Switch - Footswitch, DPDT
Great replacement for stomp-box effects requiring a DPDT (Double Pole, Double Throw) switch. AC125V/4A AC250V/2A.
$3.95
P-L300X LED - 3mm
Package of 5
Colors Available:
Package of 5. Color: Yellow, red, or green Lens Diam: 3 mm Overall Height: 5.4 mm Lens Type: Diffused Multiple color options available.
$0.65
K-960 Effects Pedal Kit - MOD® Kits, The Trill, Tremolo
The Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.
$43.95
K-965 Effects Pedal Kit - MOD® Kits, The Contortionist II, Fuzz
The Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.
$47.95
P-ECB-035 Switch - Dunlop, Footswitch, GCB-95
GCB-95 switch. This is a large double pole double throw (DPDT) effect/bypass switch for MXR and Cry Baby pedals, featuring the Dunlop “D” logo.
$9.95
P-K345 Knob - Black, Line, Set Screw, 1.0" x .6"
1.0" diameter x.6" tall, black with white line and brass insert, set screw. Similar to Dunlop knob.
$1.30
K-915 Effects Pedal Kit - MOD® Kits, The Verb Deluxe, Digital Reverb
The Verb Deluxe kit is built around the Belton Digi-Log Mini Module (P-RBTDR-2H-X) for a great digital reverb sound. The Belton Digi-Log module was built as a replacement for traditional spring reverberation units. Features include both Dwell and Mix controls, allowing the dry signal to be blended with the processed signal from a just hint of reverb to deep, cavernous echoes. The dwell control adds an extra flexibility, providing a full palette of sweet reverb sound. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$79.95
Don't see what you're looking for? Send us your product suggestions!