Integrated Circuits

P-STIC-X IC Socket - Dual in-line package, 2.54mm Pitch, 7.62mm Spacing
IC component sockets for dual in-line package chips (DIP, PDIP, DIL, DIPP.) These sockets feature ladder style cases with tinned stamped and formed connections.
Starting at $0.35
P-QTL072 Op-Amp - TL072, Dual, Low-Noise, JFET Input, 8-Pin DIP
The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
$0.70
P-Q4558 Op-Amp - NJM4558, Dual high-gain, 8-Pin DIP
Dual Operational Amplifier. The NJM4558 (JRC4558) integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip using an advanced epitaxial process. Combining the features of the NJM741 with the close parameter matching and tracking of a dual device on a monolithic chip results in unique performance characteristics. Excellent channel separation allows the use of the dual device in single NJM741 operational amplifier applications providing density. It is especially well suited for applications in differential-in, differential-out as well as in potentiometric amplifiers and where gain and phase matched channels are mandatory. Features:
  • Operating Voltage (±4V~±18V)
  • High Voltage Gain (100dB typ.)
  • High Input Resistance (5MΩ typ.)
  • Bipolar Technology
$0.90
P-QLT1054 Regulator - LT1054, Voltage Converter w/ Regulator, 8-Pin DIP
LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.
$3.19
P-QRC4558 Op-Amp - RC4558, Dual, Low Noise, 8-Pin DIP
RC4558 dual op amp in an 8-pin DIP package. The RC4558 device is a dual general-purpose operational amplifier, with each half electrically similar to the µA741, except that offset null capability is not provided. The high common-mode input voltage range and the absence of latch-up make this amplifier ideal for voltage-follower applications. The device is short-circuit protected, and the internal frequency compensation ensures stability without external components. Features
  • Continuous Short-Circuit Protection
  • Wide Common-Mode and Differential Voltage Ranges
  • No Frequency Compensation Required
  • Low Power Consumption
  • No Latch-Up
  • Unity-Gain Bandwidth: 3 MHz Typ
  • Gain and Phase Match Between Amplifiers
  • Low Noise: 8 nV/√Hz Typ at 1 kHz

Applications
  • DVD Recorders and Players
  • Pro Audio Mixers
$0.39
P-QNE5532P Op-Amp - NE5532, Dual, Low Noise, Audio, 8-Pin DIP
NE5532 dual op amp in an 8-pin DIP package. The NE5532 device is a high-performance operational amplifier combining excellent DC and AC characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage. Features
  • Equivalent Input Noise Voltage: 5 nV/√Hz Typ at 1 kHz
  • Unity-Gain Bandwidth: 10 MHz Typ
  • Common-Mode Rejection Ratio: 100 dB Typ
  • High DC Voltage Gain: 100 V/mV Typ
  • Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
  • High Slew Rate: 9 V/μs Typ
$0.65
P-QOPA2134 Op-Amp - OPA2134, Dual, High Performance Audio, 8-Pin DIP
OPA2134 SoundPlus™ Audio dual op-amp with low distortion, low noise and precision. The OPA2134 are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA2134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA2134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.
$5.40
P-QLM741 Op-Amp - LM741, Single, general purpose, 8-Pin DIP
LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.
$0.90
P-Q4580D Op-Amp - NJM4580D, Dual, Audio, DIP 8
The NJM4580D (JRC4580) is a dual opamp popularly used in many distortion pedals. This chip is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools. It is also suitable for the headphone amp at higher output current, and furthermore, it can be applied for the handy type set operational amplifier of general purpose in application of low voltage single supply type which is properly biased of the low voltage source. Features:
  • Operating Voltage ±2V~±18V
  • Low Input Noise Voltage 0.8µVrms typ.
$1.09
P-QLM13700 OTA - LM13700, Dual, Linearizing Diodes and Buffers, 16-Pin DIP
The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.
$3.29
P-QTL071 Op-Amp - TL071, Single, Low-Noise, JFET-input, 8-Pin DIP
TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.
$0.82
P-Q-AS3080E OTA - AS3080E, Linearizing Diodes, Alfa, 8-Pin DIP
The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.
$6.50
P-QTC7660 Regulator - TC7660S, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC7660S charge pump voltage converter in an 8 pin DIP package. The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+.
$1.25
P-QTL082 Op-Amp - TL082, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.
$0.34
P-QLM386NX Audio Power Amplifier - LM386N-1 / 4, Low Voltage
LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.
$1.70
P-QTC1044 Regulator - TC1044, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC1044 charge pump voltage converter in an 8 pin DIP package. The TC1044S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding –1.5V to –12V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+.
$2.90
P-QLM1458 Op-Amp - LM1458, Dual, 8-Pin DIP package
LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features
  • No Frequency Compensation Required
  • Short-Circuit Protection
  • Wide Common-Mode and Differential Voltage Ranges
  • Low-Power Consumption
  • 8-Lead TO-99 and 8-Lead PDIP
  • No Latch Up When Input Common Mode Range is Exceeded
$1.28
P-QNJM4558L Op-Amp - NJM4558L, Dual high-gain, 8-Pin SIP
NJM4558L dual op amp from JRC in a SIP8 package. The NJM4558L is the same as the DIP NJM4558 (JRC4558) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4558L is a dual high-gain operational amplifier with internal compensation circuit and constructed on a single silicon chip. It offers excellent characteristics by combining the parameters adjusted for a monolithic chip. The channel separation characteristic is suitable for measuring instruments. Features:
  • Operating Voltage ( ±4V~±18V )
  • High Voltage Gain ( 100dB typ. )
  • High Input Resistance ( 5MΩ typ. )
  • Bipolar Technology

See P-Q4558 for the DIP version of this chip
$0.85
P-QNE5534 Op-Amp - NE5534, Single, Low Noise, Audio, 8-Pin DIP
NE5534 single op amp in an 8-pin DIP package. The NE5534 device is a high-performance operational amplifier combining excellent dc and ac characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, and high slew rate. These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization of the frequency response for various applications can be obtained by use of an external compensation capacitor between COMP and COMP/BAL.
$1.15
P-QOP07 Op-Amp - OP07, Single, Precision, Low Offset, 8-Pin DIP
OP07 precision op amp in an 8-pin DIP package.These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-transistor amplifier circuit. For most applications, external components are not required for offset nulling and frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting applications. Low bias currents and extremely high input impedance are maintained over the entire temperature range.
$1.59
P-QTL062 Op-Amp - TL062, Dual, Low-Power, JFET Input, 8-Pin DIP
Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.
$0.95
P-QLM358 Op-Amp - LM358, Dual, 8-Pin DIP package
LM358 dual op amp in an 8-pin DIP package. These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems.
$0.49
P-Q-AS301A Op-Amp - AS301AN, Alfa, Single, 8-Pin DIP
The AS301AN is Alfa’s version of the LM301A in an 8 pin DIP package. The AS301A is a general purpose operational amplifier. This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvements in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry.
$1.95
P-QNE5532 Op-Amp - NJM5532, Dual, Low-Noise, 8-Pin DIP
The NJM5532 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:
  • Operating Voltage = ±3V~±22V
  • Small Signal Bandwidth = 10MHz typ.
  • Output Drive Capability = 600Ω,10Vrms typ.
  • Input Noise Voltage = 5nV/√Hz typ.
  • Power Bandwidth = 140kHz typ.
  • Slew Rate = 8V/µs typ.
  • Bipolar Technology
$1.15
Don't see what you're looking for? Send us your product suggestions!