Clearance Items

Hammond

Hammond Manufacturing offers a full range of transformers, chokes and enclosures.
P-T263-X Transformer - Hammond, High Voltage Plate & Filament, Vertical mount
  • Vertical Mount. For Horizontal Mount, see P-T263-Z
  • Primary 115 VAC, 60 Hz. - except as noted
  • Enclosed, 4 hole, chassis mount.
  • Minimum 6" long leads.
  • Units can be run full wave bridge or full wave C.T.
  • Class A insulation (105 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • Conservative designs - CSA certified (209651).
Starting at $69.95
Partially Out of Stock
Note: P-T274AX: 720 V C.T. @ 138 mA is a special order item.
P-T300-X Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
  • Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
    • NOTE: units are designed to operate with BOTH primary windings engaged.
    • See primary wiring information under resources.
  • Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
  • Highpot tested: 2,000 VAC
  • Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
  • Windings: Concentric wound for low stray field and low noise.
  • Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
  • Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
  • Conservative designs - CSA certified (209651).
Starting at $90.06
Save 9%
Originally: $98.67
P-T162XSEA Transformer - Hammond, Output, Single-Ended, 30 W
  • Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.
$223.75
P-H1590D-EDDY Chassis Box - Hammond, 26827PSLA, Eddystone 1590D, Diecast, 7.4” x 4.7” x 2.2”
Eddystone 26827PSLA enclosure with similar dimensions to the Hammond 1590D enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590D style builds.
  • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
  • Aluminum alloy to BS1490, LM2M - supplied in natural finish.
  • Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
  • Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
  • Countersunk lid holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$28.95
P-H1456W-2A-X Chassis Box - Hammond, 1456, 15° Aluminum/Wood, 4" x 5.5" x 2"
Colors Available:
15° sloped aluminum consoles from Hammond’s 1456 Series with wood sides. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes.
Features:
  • 4" x 5.5" x 2" (1” height at front)
  • Top panels are 0.064” thick aluminum
  • Powder coated top and bottom
  • Wood sides are real walnut - each piece has a unique color & grain.
  • Solid oiled walnut sides on a black, ventilated steel base.
  • Comes with self adhesive rubber feet and required mounting hardware.
Starting at $59.95
P-T290-FENDER-240 Transformer - Hammond, Guitar Amplifier, replacement for Fender, 240 V
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $63.25
P-T166-10 Transformer - Hammond, Low Voltage / Filament, Open, 10 VCT
  • Open style, chassis mount transformers with a 115V 60Hz primary and a 10V center tapped secondary
Starting at $16.78
Partially Out of Stock
Note: P-T166F10: 3 is a special order item.
P-T167X-5 Transformer - Hammond, Low Voltage / Filament, Enclosed, 5 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 5 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).
Starting at $42.78
P-H1431-18X Cover Plate - Hammond, Steel, 13.5" x 5", 20 Gauge
Colors Available:
Hammond Mfg 20 gauge steel 13.5” x 5” cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes 1/8"" holes to allow installation of optional bottom plates).
$10.90
P-H1441-8X Chassis Box - Hammond, Steel, 6" x 4" x 2"
Colors Available:
Spot welded heavy duty construction chassis. 0.036" thick. Dimensions shown are exterior dimensions. Does not include cover. See P-H1431-8 or P-H1431-8BK3
$15.75
P-T166-18 Transformer - Hammond, Low Voltage / Filament, Open, 18 VCT
  • Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and an 18V center tapped secondary.
Starting at $12.27
Note:
P-T166B18:0.54
P-T166E18:5.4
P-T166J18:18
P-T166K18:27
are special order items.
Note: some of these items are special order items.
P-H1431-20X Cover Plate - Hammond, Steel, 17" x 4", 20 Gauge
Colors Available:
20 gauge. Cover for chassis box 17 inch wide by 4 inch deep by 3 inch tall.
  • Spot welded steel - heavy duty construction chassis.
  • Finished in ASA 61 smooth grey or satin black powder paint
  • Optional bottom plates are punched with 4 holes – 3/16" diameter (Chassis requires drilling to install optional bottom plates).

Type Chassis Bottom Steel Grey P-H1441-20 P-H1431-20 Steel Black Satin P-H1441-20BK3
Starting at $9.37
Note: P-H1431-20BK3: Black is a special order item.
P-H1590A-EDDY Chassis Box - Hammond, 27969PSLA, Eddystone 1590A, Diecast, 3.6” x 1.5” x 1.2”
Eddystone 27969PSLA enclosure with similar dimensions to the Hammond 1590A enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590A style builds.
  • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
  • Aluminum alloy to BS1490, LM2M - supplied in natural finish.
  • Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
  • Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
  • Countersunk lid holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$11.95
P-H1590B-EDDY Chassis Box - Hammond, 27134PSLA, Eddystone 1590B, Diecast, 4.4” x 2.4” x 1.2”
Eddystone 27134PSLA enclosure with similar dimensions to the Hammond 1590B enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590B style builds.
  • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
  • Aluminum alloy to BS1490, LM2M - supplied in natural finish.
  • Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
  • Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
  • Countersunk lid holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$12.95
P-T166-30 Transformer - Hammond, Low Voltage / Filament, Open, 30 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 30 C.T.
  • Center tapped secondary.
  • Open style, channel bracket, two hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C).
  • Hi-Pot test of 2,000 V RMS.
  • UL listed (# E50394) & CSA certified (# LR3902).
Starting at $26.35
Note: P-T166E30: 4.5 is a special order item.
P-H1434-86 Cover Plate - Hammond, Aluminum, 8" x 6"
Hammond manufacturing 20 gauge steel cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes ⅛" holes to allow installation of optional bottom plates).
$9.10
P-H1456W-3A-BGE Chassis Box - Hammond, 1456, 30° Aluminum/Wood, 4" x 5.5" x 3"
30° sloped aluminum consoles from Hammond’s 1456 Series with wood sides. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:
  • 4" x 5.5" x 3" (1” height at front)
  • Top panels are 0.064” thick aluminum
  • Powder coated top and bottom
  • Wood sides are real walnut - each piece has a unique color & grain.
  • Solid oiled walnut sides on a black, ventilated steel base.
  • Comes with self adhesive rubber feet and required mounting hardware.
$87.90
P-H1590BB-EDDY Chassis Box - Hammond, 29830PSLA, Eddystone 1590BB, Diecast, 4.7” x 3.7” x 1.3”
Eddystone 29830PSLA enclosure with similar dimensions to the Hammond 1590BB enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590BB style builds.
  • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
  • Aluminum alloy to BS1490, LM2M - supplied in natural finish.
  • Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
  • Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
  • Countersunk lid holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$18.95
Transformer - Hammond, Low Voltage / Filament, Enclosed, 60 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 60 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).
$76.40
P-T167X-12D6 Transformer - Hammond, Low Voltage / Filament, Enclosed, 12.6 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 12 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).
Starting at $43.87
P-T185F24 Transformer - Hammond, Global Use, Dual Primary 115/230 VAC
  • Dual primary 115/230 VAC
  • 50/60 Hz. operation
  • Dual secondaries for series or parallel connections
  • 4,000 V RMS Hipot test
  • Class F insulation (155 degrees, C)
  • Chassis mount
  • Dual bobbin construction
  • Dual use terminals
  • C UL US recognized (E207860)
  • TUV Type Approved
  • CE certified to IEC 950 (Approved to EN 60-742 Safety Isolating Transformers)
$50.95
P-T850-X Transformer - Hammond, Audio Broadcast Quality, 850A Series
Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. Sealed case and wax potted core internally for stable characteristics and long life. Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.) Insertion loss of apx. 1 db.
$169.28
Don't see what you're looking for? Send us your product suggestions!