Clearance Items

P-H1590BBCE-X Chassis Box - 1590BB, Diecast, 4.71" x 3.70" x 1.18"
Colors Available:
Chassis box perfectly suited for effects pedals and other DIY projects.
Starting at $5.35
P-PATCHCABLE-X Patch Cables - 3.5mm, Mono
Colors Available:
Low cost, high quality 3.5mm patch cables in a variety of lengths and colors. The cables are super flexible, have a great droop, and are shipped coiled so no permanent kinks are formed. With the large selection of lengths and colors, these cables are the perfect choice for any sized system.
Starting at $1.39
Partially Out of Stock
P-T263-X Transformer - Hammond, High Voltage Plate & Filament, Vertical mount
  • Vertical Mount. For Horizontal Mount, see P-T263-Z
  • Primary 115 VAC, 60 Hz. - except as noted
  • Enclosed, 4 hole, chassis mount.
  • Minimum 6" long leads.
  • Units can be run full wave bridge or full wave C.T.
  • Class A insulation (105 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • Conservative designs - CSA certified (209651).
Starting at $68.82
P-T300-X Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
  • Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
    • NOTE: units are designed to operate with BOTH primary windings engaged.
    • See primary wiring information under resources.
  • Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
  • Highpot tested: 2,000 VAC
  • Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
  • Windings: Concentric wound for low stray field and low noise.
  • Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
  • Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
  • Conservative designs - CSA certified (209651).
Starting at $93.97
P-GGT-16-X Tailpiece - Gotoh, Height Adjustable
Colors Available:
This zinc diecast height adjustable stop tailpiece from GOTOH features threaded adjustable studs and knurled bushings. Hardware included. Anchor bushings: M8x1.25, 25mm height.
Starting at $14.70
P-QRECT-X Bridge Rectifier - Single-phase, 2A, In-line
2A bridge rectifier in an inline package ideal for PCB use. Features:
  • Low reverse leakage
  • Low forward voltage
  • High forward surge current capability
Starting at $0.85
P-GGT-22-X Bridge - Gotoh, Tune-O-Matic, Standard Post
Colors Available:
Bridge A modern version of the Tune-o-matic style bridge for the solidbody guitar. Pre-notched saddles with an individual saddle intonation screw retained by mini hex nuts for each one. Standard mounting post style and features hard zinc saddles. Hardware included.
Starting at $17.75
P-C70-OSC Coil - Miniature adjustable coil, 70, oscillator
Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.
$14.95
S-T212-X Nut Files - Double Edge, for guitars, 3 sizes
Package of 3
Double edge nut files featuring popular guitar gauges specially designed for slotting nuts. Each set of files is specifically designed for guitars of a particular type. This set of three files will cover the work of six and cuts a smooth round bottom slot. Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4” cutting edge
  • Set of 3 files
  • Made In Japan
Starting at $59.95
Partially Out of Stock
P-T1750X-MARSHALL Transformer - Hammond, Output, replacement for Marshall
  • Replacements for Marshall Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $49.95
P-GTFW-STEEL-X Fret Wire - Stainless Steel, 2 ft lengths, various sizes
High quality stainless steel fret wire available in popular sizes. Straight 2ft lengths sold individually or by the pound. For standard 18% Nickel-Silver options please see:
  • Small Sizes - P-GTFW-S-X
  • Medium Sizes - P-GTFW-M-X
  • Jumbo Sizes - P-GTFW-J-X

SKU Crown Width Crown Height Total Height Tang Width Stud Width Additional Info P-GTFW-STEEL-1 2.0 mm (0.079") 1.0 mm (0.039") 2.8 mm (0.110") 0.6 mm (0.024") 0.95 mm (0.037") Similar size to Dunlop 6260, Stew Mac 147, commonly used on Vintage Fender, Banjos, Pre-War Gibsons P-GTFW-STEEL-2 2.4 mm (0.095") 1.2 mm (0.047") 2.8 mm (0.110") 0.6 mm (0.024") 0.95 mm (0.037") A popular tall and narrow style, similar size to Stew Mac 141 P-GTFW-STEEL-3 2.7 mm (0.106") 1.4 mm (0.055") 3.2 mm (0.126")
Starting at $5.25
S-W130 Cord - Power, for United Kingdom plugs, 8 feet
Detachable 3 conductor power cord for United Kingdom wall outlets. Cord end is IEC connected. GTSA-3 (Marshall™ type) 18 AWG. 2-1/2 meters (about 8 feet) length, 1/4” outer diameter.
$2.79
Save 20%
Originally: $3.50
P-TF22871 Transformer - Fender® Replacement, Output, 50 W, 4 Ohm
Replacement for Bassman heads. Equivalent to #125A13A & #022871.
$53.58
Save 23%
Originally: $69.95
T-0B3_VR90 Vacuum Tube - 0B3 / VR90, Voltage Regulator
The 0B3 is a two-element gas-filled, cold cathode voltage regulator. It is designed to provide regulated outputs of approximately 90 volts.
$3.90
R-VPEC-L Potentiometer - Precision Electronics, Linear, 28mm
Linear, 28mm potentiometer with slotted solid shaft, made by Precision Electronics. 10% tolerance. 2 watts.
Starting at $5.50
Save 74%
Originally: $20.95
W-AM-AC3FDZX XLR Jack - Amphenol, 3-Pole, Female, D Flange
Colors Available:
Amphenol AC "Z" series XLR metal chassis mount connector. 3 pole female, D Flange, machined, black finish. The metal chassis mount "Z" series connectors are designed for the audio user where durability, reliability and strength across a wide range of applications are important. All AC products are manufactured to the highest quality standards and will withstand the harshest environments. Features
  • The “D” size housing can be either front or rear mounted using the same panel cutout
  • A leading first mate last break socket contact is standard on all female connectors (Pin 1)
  • Solder cup
  • Connectors are fitted with a grounding system for RFI shielding applications
  • Compatible with all other XLR brands

Note: A ground tag is standard on all AC "Z" series connectors.
Starting at $3.65
P-GTFW-J-X Fret Wire - 18% Nickel-Silver, 2 ft lengths, Jumbo sizes
High quality 18% Nickel-Silver fret wire in jumbo sizes.
  • 2.6mm - 3.0mm Crown Widths, (0.102" - 0.118")
  • 1.0mm - 1.45mm Crown Heights, (0.039" - 0.057")

Straight 2ft lengths sold individually or discounted by the pound. Per pound quantities SKU Qty Price P-GTFW-J-1 28 PRICE P-GTFW-J-2 26 PRICE P-GTFW-J-3 25 PRICE P-GTFW-J-4 22 PRICE P-GTFW-J-5 18 PRICE P-GTFW-J-6 21 PRICE P-GTFW-J-7 19 PRICE For additional sizes and options please see:
  • Small Sizes - P-GTFW-S-X
  • Medium Sizes - P-GTFW-M-X
  • Stainless Steel - P-GTFW-STEEL-X

SKU Crown Width Crown Height Total Height Tang Width Stud Width Additional Info P-GTFW-J-1 2.6 mm (0.102") 1.0 mm (0.039"
Starting at $4.95
Partially Out of Stock
P-T261X6 Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary
  • Primary 115 VAC, 60 Hz.
  • Designed for small power or bias supplies, test equipment, preamps etc.
  • Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
  • Economical , two hole, channel bracket, chassis mount.
  • Minimum 5" long leads.
  • Convenient 6.3 filament/auxiliary winding.
Starting at $38.33
W-AM-AC3FX XLR Plug - Amphenol, Female, Jaws Clamp
Colors Available:
XLR 3 pole female, stamped contacts, jaws cable clamp.
Features:
  • Zinc Diecast Shell
  • Solder Bucket connections
  • "Jaws" Cable Retention System
  • Precision machined contacts
  • Leading first mate last break socket contact
  • Quick and easy assembly without screws
$3.67
W-AM-AC3MMX XLR Plug - Amphenol, Machined Contacts
Colors Available:
XLR 3 pole male, machined contacts, jaws cable clamp. Features:
  • Zinc Diecast Shell
  • Solder Bucket connections
  • "Jaws" Cable Retention System
  • Leading first mate last break socket contact
  • Quick and easy assembly without screws
  • Precision machined contacts
$2.87
P-PG10X Pickguard - Fender®, for American Stratocaster, 11-hole
Colors Available:
Fits most American and Mexican stratocasters. 3 ply standard 11 hole pickguard. Fits 3 single coil pickukps.
Starting at $23.35
T-12AD6_12AG6 Vacuum Tube - 12AD6 / 12AG6, Heptode
Miniature heptode primarily intended to perform the combined functions of mixer and oscillator in automobile radio receivers. Specially designed to operate with plate and screen voltages supplied directly from a 12-volt storage battery.
$3.90
T-6Y6GT Vacuum Tube - 6Y6GT, Beam Power Amplifier
Beam power pentode primarily intended for use as an audio frequency power amplifier. It is particularly useful in applications where the available supply voltage is relatively low.
$5.90
W-AM-ACPM-KN ¼" Plug - Amphenol, mono, Satin Finish
1/4" Mono phone plug, diecast shell, satin finish, flexible grommet. Features:
  • Stylised Shell design
  • Robust diecast shell
  • Great solderability with increased solder area
  • Precision machined contacts
  • Flexible grommet cable protection
  • Quick and easy assembly
  • Large cable O.D. Entry to 8mm (0.315”)
$4.50
Don't see what you're looking for? Send us your product suggestions!