Circuit Design

The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features
- Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
- Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
- 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
- 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
- Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)
$6.85

The PadBoard-3U prototyping circuit board has a general purpose pad-per-hole pattern which is good for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. The PCB accepts a 96 pin DIN-41612 VME connector for backplane or board-to-board applications. Holes for ejector latches are provided. Features
- Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
- Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
- 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$12.95

ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
- Standard stripboard pattern, with tracks running the length of the board.
- Single-sided high-quality FR4 glass-epoxy circuit board.
- 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$5.50

ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
- Standard stripboard pattern, with tracks running the length of the board.
- Single-sided high-quality FR4 glass-epoxy circuit board.
- 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$9.95

The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.
$4.95

Staking tool for small eyelets such as S-HEYE-B. Directions:
- Drill hole using #42 drill bit
- Insert eyelet
- Flip board over onto a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$13.95

Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
- Sensor hole in the base of tip is fitted with a stainless steel liner
- Prevents the tip from seizing to the sensor
$5.45

Low residue, no-spill. Thermal stability enabling excellent wetting and reduced carbonization at soldering temperature. No-clean flux can be removed by wiping with a cloth or with cleaning solvent. Nonflammable and non corrosive. Recommended for electrical and electronic soldering applications.
Starting at $7.15

Single 9 volt battery box. See P-ECB-9V1B for single battery box with removable adapter. See P-ECB-9V2 for double battery box.
$13.95

Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces(epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.
$23.95

Genuine Weller narrow screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWE1010 soldering station.
- Sensor hole in the base of tip is fitted with a stainless steel liner
- Prevents the tip from seizing to the sensor
$5.45

Package of 5
Standard size terminal strip, 1/16" thick bakelite, tin plated steel lugs and brackets on 3/8" centers.
$3.45

Genuine Weller screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The screwdriver style is great for soldering through hole components. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWE1010 soldering station.
- Sensor hole in the base of tip is fitted with a stainless steel liner
- Prevents the tip from seizing to the sensor
$5.45

Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.00

Package of 3
9 volt battery clip with 5 3/4" red and black wire lengths. Simple construction and perfect for use in effects pedals. Package of three.
$0.95

Replacement hot knife tip (cat no. PSI 10) for Weller Portasol, butane soldering iron. Cut and cauterize nylon ropes and synthetic upholstery materials easily. Adjustable temperatures up to 450°C (850°F) make it perfect for cutting and shaping plastics and model making.
$16.75

Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 3/8" centers.
$3.85

The Weller WE1010 is an excellent soldering station for professional use and beginner hobbyists alike. With increased power and stability, the WE1010 is an upgrade in many ways for users of the WES51 and WTCPT soldering stations.
$135.92

Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.50

Package of 10
Colors Available:
Stake and anvil required for mounting.
- Staking Tool is our part number: S-T1715
- Anvil is our part number S-T1717
Starting at $1.88

Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
- PT Series Conical Tip for TC201 Series Iron
- PTP7 - 0.79mm / 0.031" diameter conical tip
- Solid copper, plated with iron all over
- Designed to provide maximum heat transfer from the heater to the tip
- Tinned with lead-free solder
- Use only genuine Weller tips
$5.45

Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.
$4.50

Genuine Weller screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The screwdriver style is great for soldering through hole components and many other situations. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
Starting at $5.45

Package of 120
The ZipWire™ Kit provides a convenient way to connect the signals in your projects. The wires can be unzipped for individual wires as needed and the color-coding can be used to organize power, ground and other signal types to keep your circuit organized. The rainbow colored ribbon cable provides the 10 standard electrical colors.
Starting at $9.50