Circuit Design

P-PC-ST3U StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.75
P-PC-STD15-2-BLK StripBoard - Single Sided, 6.14” x 3.15”, Vintage Spacing, Black
Black stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has 40 x 20 holes (20 strips). Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm FR4 glass-epoxy circuit board
  • HASL coated strips
  • 40 x 20 holes (20 strips)
  • 6.14” x 3.15”

Looking for projects? See our Wide Stripboard projects in our Pedal Layouts & Build Guides section for ideas.
$6.49
S-TET-SCREWDRIVER-L Soldering Iron Tip - Weller, hollow core, long screwdriver type, ET Series
Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.
$6.50
P-PC-PR1590B ProtoBoard - Fits 1590B, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190) Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
  • PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)
$3.59
S-HTUR-BI-2S Turrets - Bifurcated, for use on 2mm boards
Bifurcated turrets for use on boards measuring 2mm thick. Made of nickel plated copper. These are sometimes referred to as split or forked turrets. For use with 3mm boards, see S-HTUR-BI-3S. Stake and anvil required for mounting. Staking Tool is our part number S-T1715. Anvil is our part number S-T1717. For a budget tool set see S-T-STAKE-SET.
$2.30
package of 10
S-H160-AA-2 Battery Holder - AA, Chassis Mount, Metal Frame, Double
Metal frame AA battery holder. This battery holder fits two AA batteries and is a great option for electronics that run on 3V. It features two solder lugs for connecting wires to the positive and negative ends. The battery holder in the original FZ-1 fuzz pedals looks nearly identical to this holder.
$5.95
S-HTUR-SM-3G Turrets - Bifurcated, Screw Mount
Bifurcated turrets with a screw mount that works on boards with thicknesses of 1.5mm to 4mm. Made of gold plated brass. These are sometimes referred to as split or forked turrets. Includes a mounting washer, lock washer, and mounting nut. The staking tool is not required for these turrets.
$5.99
package of 10
S-W604X ZipWire - Jumper Cable Kit for circuits
The ZipWire™ Kit provides a convenient way to connect the signals in your projects. The wires can be unzipped for individual wires as needed and the color-coding can be used to organize power, ground and other signal types to keep your circuit organized. The rainbow colored ribbon cable provides the 10 standard electrical colors.
Starting at $9.85
package of 120
S-H-AA-1 Battery Holder - AA, Chassis Mount, Wired, Single
Prewired AA battery holder. This plastic battery holder fits a single AA battery and is a great option for vintage fuzz pedals that run on 1.5V, such as the Maestro FZ-1A.
$1.15
S-H-AA-2 Battery Holder - AA, Chassis Mount, Wired, Double
Prewired AA battery holder. This plastic battery holder fits two AA batteries. The six inch leads are prestripped and tinned stranded wire for an easy installation.
$1.30
S-TPTP7 Soldering iron tip - Weller, conical, for WTCPT
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Conical Tip for TC201 Series Iron
  • PTP7 - 0.79mm / 0.031" diameter conical tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.95
On Backorder
S-T7875B Desoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
$8.95
S-TET-SLOPED Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.95
S-TWCC104-A Sponge - for Soldering Station, for cleaning tips
Replacement sponge for soldering stations. Maintain a clean iron tip with this high quality replacement sponge. Using a damp sponge to clean a hot soldering iron helps the solder contract at a different rate than the iron, effectively removing any excess solder from the tip. Make sure the sponge is damp, not soaked, for optimal cleaning.
$1.95
S-Z3220 Digital Multimeter - YF-3220, multi-purpose
Ergonomically designed. Uses one 9V battery, included.
  • 0.5% basic DC accuracy
  • audible continuity test
  • 3 1/2 digit LCD, 0.625" high
  • 10M ohm input resistance
  • 1.5" x 3" x 7.5"(w/o rubber case)
  • overload protection
  • voltage to 1000VDC, 750VAC
  • capacitance to 20 microfarads
  • polarity indicator
  • frequency to 10MHz
  • over range indicator
  • 10A (AC or DC)
  • low battery indicator
  • hFE and diode test
  • tilt stand and case
$49.95
S-Z150 Digital Capacitance Meter - YF-150, 9 ranges
Nine ranges give precision readings from 0.1 pF to 20,000 µF. Can be used to check virtually all capacitors for tolerance value, selecting matched sets, etc.
  • 0.1 pf to 20,000 μF, 9 ranges
  • Over range indicator
  • 0.5% basic accuracy
  • Tilt stand
  • 3-1/2 digit LCD, 1" h x 2-¼" w
  • 1.5" x 2.8" x 6"
  • Zero adjustment
  • Input protected
  • Low battery indicator
  • Includes case, leads, battery, spare fuse and instructions
$49.95
P-PC-SB404 Breadboard - Solderable PCB, 3.75” x 1.85”, Mounting Holes
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.75
S-TETR Soldering iron tip - Weller, hollow core, 1.6mm, narrow screwdriver, ET Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$6.19
S-TST5 Soldering Iron Tip - Weller, single flat / sloped type, ST Series
Genuine Weller single flat style tips for use with all ST Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$6.50
S-T1714 Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$14.95
S-T7874B Desoldering Pump - Weller, manual, for removing solder
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.
$35.49
S-TSPG80L Soldering Iron - Weller SPG80L, 80 watts
The Weller SPG80L is a heavy duty 80 Watt soldering iron. It is ideal for soldering chassis connections in classic amps such as can capacitors and can be used in many other applications. This soldering iron has an indicator light that shows when the iron is turned on for safe use. The barrel is stainless steel and the rugged tip is replaceable. The impact resistant handle remains cool when in use. Features:
  • 900°F tip temperature suitable for chassis soldering and other heavy duty applications
  • Indicator light to show when the iron is on
  • 3/8” chisel tip
  • 6 foot power cord
  • Metal stand included
$49.95
P-HTAG-16 Tagboard - 300mm x 16mm, 26 Tags, single row
300mm x 16mm tagboard with a single row of 26 tags. Each connector features two lugs for easy wiring. This board can be used for stand alone projects or can be used to expand the P-HTAG-56. This board features four mounting holes.
$5.30
P-PC-PR1590BB ProtoBoard - Fits 1590BB, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590BB die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590BB enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190). Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 4 mounting holes.
  • PCB Size 3.20 x 4.25 in (81.3 x 108.0 mm)
$5.75
Don't see what you're looking for? Send us your product suggestions!