Circuit Design

S-TPTA7 Soldering iron tip - Weller, screwdriver, for WTCPT, 700F
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Screwdriver Tip for TC201 Series Iron
  • PTA7 - 1.6mm / 0.063" diameter screwdriver tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.45
S-T-STAKE-SET Staking Tool Set - Anvil and Punch, for Eyelets and Turrets
Staking tool set that includes both the anvil and swage/punch. The set works with standard turret and eyelet sizes commonly used in amplifiers. The anvil also can be used with Y style turrets.
$12.50
S-T7875B Desoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
$7.35
S-Z150 Digital Capacitance Meter - YF-150, 9 ranges
Nine ranges give precision readings from 0.1 pF to 20,000 µF. Can be used to check virtually all capacitors for tolerance value, selecting matched sets, etc.
  • 0.1 pf to 20,000 μF, 9 ranges
  • Over range indicator
  • 0.5% basic accuracy
  • Tilt stand
  • 3-1/2 digit LCD, 1" h x 2-¼" w
  • 1.5" x 2.8" x 6"
  • Zero adjustment
  • Input protected
  • Low battery indicator
  • Includes case, leads, battery, spare fuse and instructions
$47.95
P-PC-SB400 Breadboard - Solderable PCB, 3.00” x 1.90”
The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.
$4.15
P-ECB-9V2 Battery Box - Gotoh, Dual, for 9 volt batteries
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.00
S-T7874B Desoldering Pump - Weller, manual, for removing solder
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.
$30.95
S-TST5 Soldering Iron Tip - Weller, solid core, single flat / sloped type, ST Series
Genuine Weller single flat style tips for use with all ST Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$5.45
S-TETP Soldering iron tip - Weller, hollow core, 0.8mm, conical, ET Series
Genuine Weller conical style (round) tips for use with all ET Series compatible soldering irons. The concal style is great for general use and precision soldering on small contacts. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.45
S-Z3220 Digital Multimeter - YF-3220, multi-purpose
Ergonomically designed. Uses one 9V battery, included.
  • 0.5% basic DC accuracy
  • audible continuity test
  • 3 1/2 digit LCD, 0.625" high
  • 10M ohm input resistance
  • 1.5" x 3" x 7.5"(w/o rubber case)
  • overload protection
  • voltage to 1000VDC, 750VAC
  • capacitance to 20 microfarads
  • polarity indicator
  • frequency to 10MHz
  • over range indicator
  • 10A (AC or DC)
  • low battery indicator
  • hFE and diode test
  • tilt stand and case
$49.95
On Backorder
P-HTAG-40 Tagboard - 40 Turret Pins, High Quality
200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
$9.82
P-PC-ST3U StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.35
P-PC-SB404 Breadboard - Solderable PCB, 3.75” x 1.85”, Mounting Holes
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.50
P-PC-ST2 StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$4.55
S-T1714 Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$13.95
P-PC-PR1590B ProtoBoard - Fits 1590B, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190-X) Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
  • PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)
$3.40
S-TET-SCREWDRIVER-L Soldering Iron Tip - Weller, hollow core, long screwdriver type, ET Series
Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.
$5.45
P-ECB-9V1B Battery Box - Gotoh, single, 9 volt, with removable adapter
Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.
$13.95
S-TWE1010 Soldering iron station - Weller, WE 1010, 70W, digital display
The Weller WE1010 is an excellent soldering station for professional use and beginner hobbyists alike. With increased power and stability, the WE1010 is an upgrade in many ways for users of the WES51 and WTCPT soldering stations.
$135.92
S-TWLC100 Solder station - Weller, WLC100, 40 watts
40 Watts Soldering Station for Hobbyist and DIYer
  • Input Voltage: 120
  • Output Voltage: 120
  • Power Consumption: 5 - 40 watts
  • Temperature Range: 900ºF max
  • On/Off switch with "power-on" indicator light
  • Variable control produces 5 to 40 watts
  • Natural sponge tip cleaning pad
  • Ideal for hobbyist, DIYers and students
  • Includes 1/8" screwdriver tip
  • UL listed
$67.95
S-TSP40L Soldering Iron - Weller, Marksman, 40 watts
  • Weller Consumer Soldering Irons with 3 LEDs
  • Three LED lights for limited application shadowing
  • Round Co-molded soft grip handle design for easy tip positioning
  • Triangular handle area for maximum tip control
  • Stainless steel heater construction
  • Excellent quality consumer iron
  • Input Voltage: 120
  • Power Consumption: 40 watts
  • Tip Temperature: 900ºF
  • Heating Element Type: Nichrome Wound
  • Fiberglass and ceramic insulated
$27.95
S-W604X ZipWire - Jumper Cable Kit for circuits
Package of 120
The ZipWire™ Kit provides a convenient way to connect the signals in your projects. The wires can be unzipped for individual wires as needed and the color-coding can be used to organize power, ground and other signal types to keep your circuit organized. The rainbow colored ribbon cable provides the 10 standard electrical colors.
Starting at $9.50
P-HTAG-16 Tagboard - 300mm x 16mm, 26 Tags, single row
300mm x 16mm tagboard with a single row of 26 tags. Each connector features two lugs for easy wiring. This board can be used for stand alone projects or can be used to expand the P-HTAG-56. This board features four mounting holes.
$5.25
S-TET-SLOPED Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.45
Don't see what you're looking for? Send us your product suggestions!