Circuit Design

Eyelets, bag of 10 (mounts in 1/8" hole).

Turrets for use on boards measuring 2mm thick. For 3mm boards, see S-HTUR-BX
Stake and anvil required for mounting.

• Staking Tool is our part number: S-T1715
• Anvil is our part number S-T1717

Turrets for use on boards measuring 3mm thick, such as P-HTUR-C or P-HTUR-B. For 2mm boards, see S-HTUR-AX
Stake and anvil required for mounting.

• Staking Tool is our part number: S-T1715
• Anvil is our part number S-T1717

Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10

Vulcanized Fiberboard, used for laying out circuits using eyelets such as S-HEYE-A and our staking tool S-T1715.

• .062" thick
• 3" x 15"

Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.

Hollow Turret Terminal,Brass, .172" Long, Premium.

• Finish/Plating: Tin
• For Panel Thickness: .125 [3.2]
• Material: Brass
• Mounting Hole: 0.116
• Terminal Length: 0.312
• Terminal Style: Tubular Turret
• Type: Solder Turret Terminal
• Package of 10

Tin plated brass eyelets commonly used on vintage style pickups. The small sized eyelets are also great for smaller point-to-point projects such as DIY stomp boxes. The outside diameter of the barrel is 0.089” and the recommended mounting hole is 0.093” using a #42 drill bit.

5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets. 6 lugs, first and sixth lug are common.

60/40 Rosin Core, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.

Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.

High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.

Genuine Weller screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The screwdriver style is great for soldering through hole components and many other situations. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station

Variety pack, 10 feet for each color. 6 colors, 60 feet total. 600V stranded. Strands are tinned individually. See photos for detail. UL style 1015, rated to 105 degrees C. Perfect for new projects or rewiring any electrical equipment.

Variety pack, 10 feet for each color. 6 colors, 60 feet total. Great for color-coded wiring with smaller quantities.
600V stranded. Strands are tinned individually. See photos for detail. UL style 1015, rated to 105 degrees C. Perfect for new projects or rewiring any electrical equipment.
Included colors:

• Black
• Red
• Green
• White
• Yellow
• Blue

See S-W33 for 50 foot rolls of individual colors.

Kester 44 60/40 rosin core type. .031" diameter, 0.5 oz

Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:

• Drill 1/8" hole
• Insert eyelet
• Flip board over on to a hard service
• Center staking tool over the eyelet
• Strike staking tool with hammer to clamp eyelet to board

300mm x 56mm tagboard with two rows of 28 tags. Each connector features two lugs, one facing inward and one facing outward. This can be helpful when connecting components using the inner lugs which leaves the outside lugs open for wiring. A center row of holes can be used for running wires beneath the board as well as for standoffs.

Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.

Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.

• ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
• Precision ground copper tips are plated with iron, nickel and chromium
• ST7 - .031" / 0.79 mm diameter Conical tip
• Tinned with Lead Free alloy

Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:

• Low profile 0.180" standoff height.
• Offset base allows use when holes are close to the PCB edge.

Turret anvil for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For staking tool see S-T1715
Directions:

• Drill 1/8" hole
• Insert eyelet
• Flip board over on to a hard service
• Center staking tool over the eyelet
• Strike staking tool with hammer to clamp eyelet to board

(63/37 Rosin Core) - ..031" Diameter, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.