Washer fits around sockets to hold them to chassis.

Washer fits around the socket in in order to hold it to the chassis. for 8 pin sockets.

Genuine Bigsby® flat handle bracket for use with Bigsby vibrato units. Includes set screw for mounting to vibrato. Arm and other hardware sold seperately.
Not compatible with Lightning Series vibratos.
For handles see P-GB-HANDLE-1X.
For 9.5" handles see P-GB-HANDLE-8X.
For handle fiber washer see P-GB-WASHER-1.
For handle pivot spring see P-GB-SPRING-3.
For handle nut see P-GB-NUT.
For complete handle assemblies see P-GB-HANDLE-6X.

Genuine Bigsby® Chet Atkins fixed handle bracket for use with Bigsby vibrato units. This bracket sets the handle into a fixed position whereas the P-GB-BRACKET-1X versions offer a pivoting arm. Arm sold separately.

Ceramic Tube socket used for octal power tubes.

• Chassis hole: 1” to 1-1/4” depending on mounting (Top: 1” to 1-1/16”, Bottom: 1-1/4”)
• Mounting Centers: 1-1/2” with oblong mounting holes

Ceramic Tube socket used for octal power tubes.

• Chassis hole: 1” to 1-5/32” depending on mounting (Top: 1” Bottom: 1-5/32”)
• Mounting Centers: 1-1/2” with oblong mounting holes

Linear. 16mm body size (mini type) Snap-In pot with mounting bracket. D-Shaft ¼", ½" length shaft. 7mm bushing, ¼" bushing length. PC Mount. Nut and washer included

Features

• Economical "open bracket" - channel mount.
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C.

Audio. 16mm body size (mini type) Snap-In pot with mounting bracket. D-Shaft ¼", ½" length shaft. 7mm bushing, ¼" bushing length. PC Mount. Nut and washer included

Reverse Audio (30C). 16mm body size (mini type) Snap-In pot with mounting bracket. D-Shaft ¼", ½" length shaft. 7mm bushing, ¼" bushing length. PC Mount. Nut and washer included.

Linear. 16mm body size (mini type) Snap-In pot with mounting bracket. Solid Shaft ¼", ⅜" length shaft. 8mm bushing, ¼" bushing length. PC Mount. Nut and washer included.

Ceramic Tube socket used for octal power tubes, PC mount

• Chassis hole: 1” to 1-1/4” depending on mounting (Top: 1” to 1-1/8”, Bottom: 1-1/4”)
• Mounting Centers: 1-1/2” with oblong mounting holes
• PC mount pins

Linear snap-in style pot with bracket, PC mount, 17 mm body diameter, 7 mm bushing diameter (M7 x 0.75), 5 mm split knurled shaft. Mounting hardware not included.

Audio snap-in style pot with bracket, PC mount, 17 mm body diameter, 7 mm bushing diameter (M7 x 0.75), 5 mm split knurled shaft. Mounting hardware not included.

8 pin socket saver with bracket. Commonly used in tube testers. Socket savers absorb the main wear and tear from many tube insertions and removals. It's much easier to replace a worn out socket saver than to replace the original socket.

This pickguard mounting bracket is a direct replacement for contemporary Gibson® Les Paul® guitars. It is USA made component with high quality plating to the standards you would expect for your guitar. Slight differences include the adjustment slot having rounded ends instead of the original square cut slot and a slight difference in width from the historic version. Mounting hardware is not included.

100K Dual Reverse Audio with bracket.

New production, aluminum, 2" tall, for use with P-ST9-700 and P-ST9-700-PC.

Linear taper, vertical mount, Song Huei pots with a 6mm shaft. These 9mm pots are popular in DIY guitar pedals, modular synthesizers, and other projects where space is limited. The knurled shaft features a painted indicator line so no knob is required. These tall versions have a 17mm shaft length and a total height of 25mm. For audio taper versions, see R-VSHL-AX. For center notched linear taper versions, see R-VSHL-BX-CN.

Audio. 16mm body size (mini type) Snap-In pot with mounting bracket. Solid Shaft ¼", ⅜" length shaft. 8mm bushing, ¼" bushing length. PC Mount. Nut and washer included.

3.5mm TS jacks with a switched tip found in many DIY Eurorack projects. The WQP-WQP518MA-BM is the new improved version of the WQP-PJ301BM featuring Qingpu’s rugged square based bushing. The sleeve connection is through the outer bracket that snaps into place on the pcb allowing for easy construction and panel fitting. Hardware sold separately. See accessory items below.

Heavy duty swivel caster for use on Fender and other amps. Each 2" diameter wheel supports 45.359Kg / 100Lb.

Tweed style hand mounting bracket hardware for P-H262, P-H263, P-H315, and P-H282 amp handles. Sold individually. Screws not included. Multiple color options available.

Includes all parts but the magnet wire, all sets are ready for winding. Kits include Alnico 5 magnets, bobbins, poll screws, slug screws, baseplate, and coil lead wires.